20 Most Recent Pro-Fit Pro.Fit Dg 71 01 Dodge Dakota Pickup/Durango 01 Up Questions & Answers

Fuel gauge is pretty simple. Usually a 3 wire set-up. Power ground and gauge. If you find the power feed and ground it the gauge should go to full. Other way should go to empty.

Might be the crank sensor, but you would need an engine scanner to test that. Some auto parts stores will hook a scanner up for free if you buy the part there. I dont know if you can get it there, but you need to see if the scanner registers RPM's when it is cranked over. This would be a starting point.

check the automatic choke, or the distributor vacuum advance for a possible leak.

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

suspect gauge is faulty

If you are just cleaning the outside there is a kit with very fine sand paper and a uv protectant at the auto parts house. If you still need to remove the lens the screws are very hard to ge to and underneeth the bumper once removed you will need to seal them back with rtv.

Tensioner only moves about an 1 1/2inches. If it is moving that much and you still not able to get the belt on you may wanto to double check the belt looping to insure it is correct. Most vehicles have a sticker near the radiater or on hood that shows belt wiring.

normally you just have to start it right away. replace the battery in your wireless unit.

You reverse sensor switch needs to be checked/ replaced. check your rear light assembly and sockets.

1. service engine 2. replace airbag 3. actuator or switch is going out. If you hear the door trying to unlock it is the actuator if you don't it is the switch.

The radio code is a security feature that's meant to deter theft, and it's unique to each vehicle. If you've lost your code, you'll need to contact a Nissan dealership or service center and provide proof of ownership. They should be able to help you retrieve the code. Please do not attempt to use codes from the internet as incorrect attempts may lock your radio.

How to change language to english for Honda Odyssey 2021 Gathers Radio Player

I have the same radio now with no Bluetooth am trying to get Bluetooth on it too without having to buy another radio. Please help.

First thing to do is check to make sure that the batteries are properly charged.

Second, make sure that you have a clear line-of-site to the IR transmitter. Infrared (IR) works the same way that your TVs remote control works - if the signal is blocked, then you will not hear any sound.

Third, make sure that you are in the rear seat of the vehicle when listening to the sound. The IR transmitter only transmits to the rear seat, so you will not hear any sound if you are sitting in the front seats. This is a common problem that i see.

Lastly, make sure that the heapdhones you purchased are compatible with your 2006 2007 2008 2009 or 2010 Toyota Sienna. Remember that some older models require RF headphones, not IR headphones. I checked http://www.audiovideo2go.com for compatibility before I purchased my headphones. They have a useful listing of all the headphones and models of vehicles they are compatible with.

'make model (what is is)' as first 3 words in all questions. https://www.google.com/search?q=demo+mode+the+code+for+4.91 ..

Unfortunately, no one knows or is telling. Companies rarely state power in RMS because Peak Power is a much more impressive. 1000 watt amp, 200 watts RMS x 2 channels at 8 ohms. Look for a sticker on the unit. https://www.google.com/search?q=Xplore+Amp+5553 ..