20 Most Recent ASUS P5N-E SLI Motherboard Questions & Answers

Flash your bios

Honestly, it sounds like there might be a RAM issue. Personally, I would remove all the RAM chips (assuming that you have more than 1 installed). Then Place 1 Chip in and check to see if the machine boots up. If yes, great.. 1 good chip, shut down, remove chip, try another one. If still No, shut down, remove chip, try another one. Please keep in mind that some of the older systems especially need to run in pairs, so you might have to try different combinations of 2 to see if this is the problem. Hope this helps.

You go to AVIRA dot com and download the boot tool, or go to BITDEFENDER and run an online scan, you don't put in a new HDD just because you had a virus, it sounds like you had a problem and thought it was a virus.Read you manual, plug in the Sata drive into Sata 1.Do you mean BIOS post, if you don't even see the BIOS post, check your monitor with another PC.There is only one correct power switch pin, a , + and - pin, how can you switch, there is no such thing as switching.

You get this error code if there is an issue with the drivers.Look here:http://answers.microsoft.com/en-us/windows/forum/windows_7-hardware/usb-ports-not-working-error-code-43/ce6662bf-cfad-4380-a274-709bf072e3d7Here is the homepage:http://support.asus.com/Download.aspx?SLanguage=en&m=P5N-E%20SLI&p=1&s=22Please select your windows system.You probably need to download the chipset driver.Open the folder, and click on global for download.Unzip the file before you install the driver.Look also in the bios setup, for the usb settings.Try also to download the manual.Try also to upgrade the bios.Hope this will help you

Test all power and data leads that attach to your hard drive IDE,SATA

the leads from your MOTHERBOARD TO YOUR HARD DRIVE make sure they have a secure dust free connections and are not faulty or just replace them they could be faulty make sure all leads that are attached to your drives dvd\cd 3 1/2 inch floppy have secure connections and are not faulty even the electrical extensions or just replace them they could be faulty a computer needs its connections to continue its cycle and have an end so any faulty leads will end up with a computer error even something as small as a faulty power lead can cause you problems

computers need power and data travel through every working device and to have an end to be able work properly

make sure ram modules and cmos batteries have dust free secure seatings and cmos battery has charge some motherboards cmos batteries are soldered in

motherboard and a hard drive any leads between them will fail before your motherboard or your hard drive if its a flat ribbon 40 pin type IDE replace it this will be the first to fail

check all power and data leads make sure they have secure dust free connections

cd/dvd floppy drives need to have current go through make sure these drives are working

check you CPU make sure its securely seated and has thermal grease hope this helps

YES

By clicking the below link you will get the driver what you needed. Click here to go to your driver link. Thanks for usig FixYa.

http://www.mercury-pc.com/downloads_list.php?productid=857
download driver here
i hope this helpful
thank you for using fixya

Motherboards have a "timed-wake-up" option.
You can enter BIOS SETUP, and configure the computer to wake-up at a specified time, e.g., 01:35, on specific days, e.g., "daily".

Restart your computer.
Enter BIOS SETUP
Set the computer's clock to 01:30.
Save the setting
Exit from BIOS SETUP.
Turn the computer off.
Wait 5 minutes, until the computer's clock advances from 01:30 to 01:35, and watch what happens.

Keep in mind that if your board has a different BIOS, this may not apply:
ASUS beep code

It doesn't appear to be a RAM or CPU problem. It could be the motherboard (maybe the SATA controller), or the hard drive. There are two thinkg you can try:

1 - connect the hard drive to another SATA port, and change the boot order in the BIOS to point to the new port. If it works then it's a problem of that specific port. (motherboard problem)

2 - connect the hard drive to another SATA port on another controller. If you have the hard drive connected to a red port, try a black port. If it's connected to a black port, try a red port. If it works then it's the controller. (motherboard problem)

3 - try to install the OS on another hard drive and connect just that hard drive. If it works, then it's an hard drive problem, and you can replace that.

No, it needs a video card, of any kind, with a monitor attached to power up.

Beep codes .
Navigate to this page click HERE!

There is no problem with your hardware, but your software. I do not prefer using 64 bit applications/software since they are a bit unstable. Why not use just 32 bit since it has no problems?

We don't need to upgrade if we can't use it.
hehe

Yes as long as the 9800gtx is PCI Express x16. I am assuming the p5n-e is the Asus MB. Since I couldn't find any other Manufacturer using that MB#

double check memory slots make sure they are paired correctly- try just 1 stick in the a and then b slot

Hi.

Unplug you PC.
Reset Bios by removing the baterry for 10 minutes just to make sure it resets propely.
Restart the computer. see if any image appears on screen. if it does, configure your bios date, time etc.

Then you are done. If that dosnt help.. Go to a technician and ask him to change the condensors arround your processor..

you can check your video card or memory card if it is placed correctly. or else, try to remove the cards and clean the pins with an eraser so that corrosion will be removed. then gently place the cards into the slots and try to press them quite hard for them to establish good contact with the boards slot. start your pc and see what happens.