20 Most Recent EuroTech EWF172 Front Load Washer Questions & Answers

you could check the drainage hose to see if there are any kinks or clogs. sometimes the water has no where to go because the hose has some material stuck inside of it.

Could be that one of the support struts or springs is broken. Take off the top and back and feel the springs and support struts. If one is broken you should be able to see it. In sister's machines, the problem was a broken spring and a broken shock absorber.

Hope helps.

If the clothes go to one side it will make that loud noise. open it up when it startes to make that noise, make sure clothes r even around and not push all to just one side.

Here is a link to the part and video on how to install it.
http://www.apart4u.co.uk/electronic-module-servis-m3902-opn-546001403.html

try this link to a PDF owner's manual

http://www.creativelaundry.com/owner_services/ProductSheets/Eurotech/EWF150-EWF172om.pdf

hello. the belt on your machine is old, tired and worn. As a result it will only work when it is not asked to do too much. Replace the belt and the pulley and you will be good as new. If you have Sears stores nearby you can get parts there. Go to searspartsdirect.com then enter your model number and a complete parts diagram will appear. IF not, any store that sells appliances will have a source for the parts. Joe

Go to partselect . com or daysappliance. They will have the part, the diagram, and more. Awesome sites. They new seal should come with the adhesive as well. After your rip off the old one, clean the surface really well before applying new adhesive and seal.

hello you may have an hole in the door seal check the rubber seal around the door if this is ok then check rubber hose on the pump

regards
shaun

Hi,
If you are having a problem with your top load washer then check out this tip...

Washing Machine does not Pump or Spin
http://www.fixya.com/support/r4617986-washing_machine_not_pump_or_spin

If you are having problems with your front load washing machine then checkout this tip...

Front Load Washing Machine not draining and or not spinning
http://www.fixya.com/support/r4784376-front_load_washing_machine_not_draining

heatman101

Hi


Thanks for using FixYa. To resolve the issue you’ll need to check so many things like the filter might be clogged, exit spigot might be clogged if the filter is clean, clogging of the path between the tub and the pressure sensor which senses the water level in the tub. Clogging can result in water level being incorrectly detected (may read as too high or too low) for the stage of programme that is executing, which can result in a halt of the programme. Please also check if some small clothing got stuck between the tanks, bad transmission, bad thrust bearing or brake hanging. If still the issue persists, then there should be air for passage in the standpipe on the back of the washer. Please check that the hose should be fitted airtight into the standpipe. Please do accept the solution if the issue is resolved or else revert for further assistance.



Thanks
Rylee

Make certain that your selected wash cycle designates a higher spin speed. If so, then you may have an issue with the motor or motor control board. Contact an appliance service company.

Hi,
To have the washing machine drain properly you would need to do the following steps:
Open the case, and disconnect the water hose from the outlet of the water pump.
If you get water pouring out from the pump, then plug that up and check the hose to the sewer. If that is clogged, then you have found the problem.
Some washers have a self cleaning filter in that hose somewhere. Check that to be sure it is working properly.
Next plug back the washing machine.
Thanks for contacting fixya.com

Possibly the inlet valve has taken in grit from the water supply, and is blocked. The machine will have to come out to fix this one buddy!

Check Lid switch/pressure switch if rest of cycle operates normally , then that can be the problem.