D-Link D Link Dir 601 Wireless N Home Router Transmission Speed 1875 Mbps Maximum Frequency 240 Ghz - Answered Questions & Fixed issues

Is your Hughes net modem working - check by connecting directly to it using a LAN cable. New check the LAN cable from our modem to the router - try a new cable. Reboot both devices. Login in using your browser and go to WAN settings and the wireless settings and set-up a wireless password/key. Remember the key because each device will now need it to connect. You can also turn OFF Broadcast SSID and your network name will not be shown on anyone's device. You must remember the network name when using this method. When all else fails, The final solution is a factory reset of your router. You can do a factory reset by logging into the router using you browser. Go to the settings and perform a factory reset If you forgot the router password, you ill have to do a factory reset by locating a small hold on the back of the router and insert the tip of of paper clip for about 10 seconds while the power is on. The router will be reset to out of box status and then you can set-up form scratch.

Check LAN cable between the router and internet modem. If OK reboot both devices. Connect directly to your internet modem make certain it is connected to the internet properly. When all else fails, The final solution is a factory reset of your router. You can do a factory reset by logging into the router using you browser. Go to the settings and perform a factory reset If you forgot the router password, you ill have to do a factory reset by locating a small hold on the back of the router and insert the tip of of paper clip for about 10 seconds while the power is on. The router will be reset to out of box status and then you can set-up form scratch.

Probably can, but you posted this on the Fixya router section.....

Connect via cable tot the router.. Go to 192.168.0.1 in the internet explorer. Put user name as admin and password as admin. Check password onwifi setup screen. You can change the password too.. Now Remove cable and connect via wifi witht the new password.

Post to Cars & Trucks category for a Car expert.

This would be a password either setup by default or by whomever set up the router in the first place. There also maybe a pin you can use written on a label on the router itself.If not, then you will need to reset the router by pressing and holding the rest button on the router for 15-20 seconds. Once it is reset you will need to reconfigure the router.

To setup SSID and Security Key use the Manual : http://www.dlink.com/ca/en/support/product/-/media/Consumer_Products/DIR/DIR%20601/Manual/DIR-601_Manual_US.pdf Wrie down the Security Password/Key and keep for futurw use.

First open the browser ->put the IP address(normally IP address of d-link router is 192.168.0.1 but you should check the manual ) ->login using username and password.Go to the "Security" tab or option and click on WEP or WPA, select the encryption, choose a password and click save or apply.If you need any kind of technical assistance you can contact for Router support

If the default password on the D-Link has been changed then -To reset the D-Link back to the default settings -Press and hold the RESET button at the back of the router with the power ONuntil the LEDs flash at the time the release the RESET button. (firmware version was 3.00, and upgraded to3.05)Connect a LAN cable from the D-Link to your laptop/computer'sLAN port, open the browser on your laptop/computer and enter the D-Link's configurationURL..http://192.168.0.1The default login = adminThe default PW = blank (just press Enter)You can now change the default adminpassword.You can now configure the wireless settings. Now configure the wireless card in your computer/laptop withthe router's wireless settings.To secure your wireless network from unauthorized access,please click on this link and follow my instructions :-http://www.fixya.com/support/r3559128-wireless_router_security

To connectyour computer to a wireless router, you click the Refresh networklist, then Choose your wireless network and then click Connectto your secured Wireless Network, it will asks for a Network Keybefore allowing you to connect into your wireless network. This NetworkKey is either the WEP, or WPA or WPA2 Encryption key that is used toconfigure the Wireless Router. The Passphrase is an alternate way tosetup the Encryption key.When you are requested for a Network Key, you can just enter the Passphrasethat was used to configure the Encryption key in the wireless router.http://www.fixya.com/support/r5270415-network_password_network_addressFor information on securing your wireless network,configuring the wireless router and configuring the wireless card in thelaptop/computer, please click on this link and follow my instructions :-http://www.fixya.com/support/r3559128-wireless_router_security

I think you should try to reset and reconfigure it manually.Connect the modem and computer to the router.Reset the router.OPen the setup page.Change the settings.See How to setup router

YOU NEED TO CALL YOUR INTERNET PROVIDER TELL YOU PROBLEM THEY WILL SORT YOU OUT.

Are you pertaining to your network key?These are the steps for you to modify the passcodes fields via router settings.Follow this instructions:1. connect via hard wired connection using your PC (network cable)2. open your internet explorer or any browser.3. type the numbers 192.168.1.1 on the address bar4. you will be routed to your router's settings, type admin for USERNAME: and admin for PASSWORD.5. look for the basic setup/settings6. look for the wireless settings7. under your SSID comes the WEP or WPA-PSK option8. that is your wi-fi password, then modified it and remember the password you use for you will need to enter it on your pc when you are connecting via wireless connection.you can select ASCII for password. it should be alpha numeric or combination of letters and numbers.9. select save and apply. then you are good to go.thanks for choosing fixya.com and kindly rate this post.

Follow this instructions:1. connect via hard wired connection using your PC (network cable)2. open your internet explorer or any browser.3. type the numbers 192.168.1.1 or 10.1.1.1 on the address bar4. you will be routed to your router's settings, type admin for USERNAME: and admin for PASSWORD.5. look for the basic setup/settings6. look for the wireless settings7. under your SSID comes the WEP or WPA-PSK option8. that is your wi-fi password, then modified it and remember the password you use for you will need to enter it on your pc when you are connecting via wireless connection.you can select ASCII for password. it should be alpha numeric or combination of letters and numbers.9. select save and apply. then you are good to go.thanks for choosing fixya.com and kindly rate this post.

Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. If you are still not able to access router with above ip then you need to RESET it for that press RESET button for 10 seconds it is in back side of router then all settings defaults..Then you can access it with above method. Then click on WAN settings set it as your internet service provider settings enable DHCP Then click on wireless and enable it. . Then click on wireless->wireless security->WEP security there is code password note down it or enter new password then save setting s and restart router. then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa.

You can find the details of the operator and the state they belong to .the operators wont reveal the address and name of any mobile numbers only higher officials can only get those information.
In order to trace the operator name and state you can try this link
http://www.indiatrace.com/trace-mobile-number-location/trace-mobile-number.php

I hope this will help you if it does do rate the answer
Thank you
regards
lalith

I am sure it is now toast and you cannot downgrade if the wrong firmware has been installed. I would ask D-Link.

https://www.youtube.com/watch?v=zKeXtyUMKjA Check out this video it might help you with your issue.

Please open router page and go to advanced just like in this emulator. http://support.dlink.com/emulators/wbr2310/adv_network.htm

try changing the channel number from auto to a channel number 2 or 3 higher than the lowest channel number.' do this by logging into the d-link dsl 2640