20 Most Recent Sanyo PLC XU30 Multimedia Projector - Page 6 Questions & Answers

I will send the manual to you by email, if you need We supply original projector lamp,bulb,parts,Lcd panel,Lens,DMD chip,color wheel,motherboard,powersupply,ballast... with high quality and competitive price. any questions, feel free to contact me have a nice day! Jerry,Lampdeng Limited

Suspect shut down due to an over-temperature condition. Owner's Manual page 69 shows WARNING TEMP indicator at the top left which would be blinking on an over-temperature shut-down. In an over-temperature condition the manual states that the following should be done....
- Did you provide appropriate space for the projector to be ventilated?

Check the installing condition to see if the air vents of the projector are not blocked.

- Has the projector been installed near an Air-Conditioning/Heating Duct or Vent?

Move the installation of the projector away from the duct or vent.

- Is the filter clean? Clean the filter periodically or replace it with a new one.

However, if the WARNING TEMP lights red (steady) then an abnormal condition has been detected....

When the projector detects an abnormal condition, it will be automatically shut down to protect the inside of the projector and the WARNING TEMP. indicator lights red. In this case, unplug the AC power cord and plug it, and then turn on the projector once again to verify operation. If the projector cannot be turned on and the WARNING TEMP indicator lights red, unplug the AC power cord and contact service.

Finally, the POWER indicator which is at the bottom right of the group of indicators would blink after the lamp has turned off but the fans would still be running during a critical cool-down period where the AC must not be disconnected until the indicator stops blinking (is steady).

If you do not have access to the manual, one can be downloaded from us.sanyo.com at this link...
http://us.sanyo.com/Projectors-Products-by-Category-Discontinued-Models/PLC-WTC500L

Have a good day! any question ,contact me,Please We supply original projector parts: lamp, bulb, Lcd panel, Lens, DMD chip, color wheel, motherboard, powersupply ... with high quality and competitive price. Jerry Lampdeng Limited Mobile: 0086-13178867858 Wechat ID: 008613178867858 Whatapp ID: 008613178867858 Skype: [email protected] http://www.lampdeng.com

there are a lot of dust on the Lcd panel 3 panels (red ,blue,and green) in the Projector purple speckles means that the dust on the Green , 1,pick the Lcd prism from the projector 2,clean it by putting it into water,with some cleaner 3,dry it with a hair dryer 4,ok Have a good day! We supply original projector parts: lamp, bulb, Lcd panel, Lens, DMD chip,color wheel, motherboard, powersupply ... with high quality and competitive price. Jerry China Lampdeng Limited Tel: +86 131788 67858 E-mail: [email protected] Skype: lampdeng.com YM: [email protected] http://facebook.com/lampdeng http://www.lampdeng.com

Lamp LED should be lit when the projector is in Standby. However, the problem you are describing sounds like one of two issues. Either the lamp is bad and needs replaced, or there is a power supply fault. If you have tried replacing the lamp already, make sure you reset the lamp counter or the projector may still not function properly. does the temp warning light come on when the projector shuts off? if so you may also try cleaning the air vent filters and ensure there is proper air flow around the projector. if that checks out then have the projector serviced as the power supply is likely suspect.

follow the steps and your owner manual read from computer or proyector download from www.fitness.manualsonline.com or www.retrevo.comHowever you must use THE key FN for setup the proyector in your computer.God bless you

There ar a few reasons that will occur. The main two are,
If there is no signal and if it is overheating.
If there is no signal. that is an easy fix and so is the overheating.
Consult your instruction manual and remove the filters, clean the air intakes and filters and refit the filters.
Hope that helps.