Top 20 Maxent MX-26X3 Television Questions & Answers

0helpful
1answer

The TV doesn't power up

If power reaching unit and after all you have checked, it appears the PS is fubar. Easiest thing to do is check for swollen/leaking/blown capacitors and replace them - cross your fingers and turn on.
9/4/2017 2:39:03 PM • Maxent MX-26X3... • 110 views • 0 helpful votes
0helpful
1answer

I have a Maxent MX-26X3 Television and I cant get it to connect to the local channels when I plug in an antenna. What am I doing wrong?

Do you have a digital converter box? Its a smaller block square box that connects to the wall and the tv connects to the digital converter? I you do not have a digital converter that is most likely your problem. Not a gurantee but since they did the big digital signal switch, you now need these converters. Hope this helped
10/26/2012 1:35:04 AM • Maxent MX-26X3... • 289 views • 0 helpful votes
2helpful
1answer

Maxent mx-26x3 video issue

The tv probably does'nt have a fast enough refresh rate to work with games properly. It should be in the manual for the tv, the lower the number the better. I think it's 12 milliseconds on that tv. Have a look here:Response Rates.
4/15/2012 3:53:47 AM • Maxent MX-26X3... • 258 views • 2 helpful votes
0helpful
1answer

Do you have a picture or can you tell me where that

what are you looking for? If someone answered a prior question make a comment there or here describing what you need to know.
5/28/2012 2:06:15 AM • Maxent MX-26X3... • 43 views • 0 helpful votes
0helpful
1answer

How can i fix static on my maxent lcd tv

26 inch maxent mx-26x3 and 32 inch, l2614xw02 some same parts When i hear the word static, i think snow,If while your watching tv and it looks like color snow pixels popping in and out all over the picture i did this to fix it.look at main board you see a green heat sink,left of that heat sink you see a 220 uf 16 volt capacitor that half surround by 22 uf capacitors,change the 220 uf capacitor and snow is gone.to get it off i just wiggle slowly back in forth until the old capacitor falls off,then put some fresh solder on and new capacitor on and done.use a radial electrolytic capacitor not the little metal one they had ontc bagabillion
7/11/2011 12:53:56 PM • Maxent MX-26X3... • 220 views • 0 helpful votes
1helpful
1answer

Maxnet mx-26x3 tv toconnect toan HDMI input

Maxent ,mx 26 x3 turns on for 5sc.( all white) then picture flickers and screen goes black.. green light on throughout..none of button on the remote or the tv will work expect the power .i wonder is their a way to reset the tv?
6/10/2011 7:49:06 PM • Maxent MX-26X3... • 305 views • 1 helpful votes
0helpful
1answer

Need the base ( stand

Here's the LINK.
5/19/2011 1:24:39 AM • Maxent MX-26X3... • 149 views • 0 helpful votes
1helpful
1answer

Can I use this as a PC monitor via adapters of

yes you can and fromwhat i see you have the right connection on the monitor so you dont need any special adapters - you just need a 15pin VGA cable with audio (mini phono for audio) male for all connections on both sides of wire

connector should look like this

images?q=tbn:and9gcrnfpwdbn3a_ozkr8hzprr_0j3o4i2krz2rpdz4etcsoyfnzl-ojljg5oa

wire should look lilke this

images?q=tbn:and9gctsz2vwsxpd1w5napqnc2bhy7vmotwfe6wqhougqythkgf7tbamghnselmx

hope this helps

good luck!!
3/29/2011 5:23:36 PM • Maxent MX-26X3... • 119 views • 1 helpful votes
0helpful
1answer

My screen will be okay for about 30 seconds and

Problems on your video board and also maybe power supply problems, the caps in most of these sets are the blame. So look for bad caps, you tube has video on how to fix some sets
1/3/2011 4:09:42 PM • Maxent MX-26X3... • 104 views • 0 helpful votes
0helpful
1answer

When tv heats up picture goes away set is only 4

I had a similar problem with my 42 in Philips LCD HDTV.



Here was the problem. My Power Supply Board had several bad capacitors. I opened my TV (warranty was expired of course) and found four bulged capacitors. Many electronics companies were sold capacitors that failed in 2-5 years instead of 10-20. The capacitors fail prematurely due to a lack of preservatives. Unfortunately, they were installed in all sorts of devices and cause a wide range of failure problems.


Here are some options for you.



1. Have it fixed by a professional $$$$$$$???????



2. Open your TV and find PSB. Check for faulty caps. If you find some (bulged or leaking) bad caps replace the entire board. The entire board costs around $250 right now because they are in high demand right now. They can be found at tv-part.com but supplies are limited.



3. Remove and then replace individual faulty caps. This takes some soldering skill.

Caps are inexpensive and if you can take care of it yourself it will save you hundreds.



I have a tip/tutorial on this site that may also help. It gives step by step instructions for replacing caps on PSB #715t2432-2. If this is your board you are in luck. It's called: Fixing the Philips Turns/shuts off on its own problem. I'm working on uploading pictures to help guide people though the process as well. Let me know if I can do anything to help.


Hope this helps and Good luck.


Kaufman605

12/12/2010 8:52:11 PM • Maxent MX-26X3... • 126 views • 0 helpful votes
0helpful
1answer

Screen is black but sound

You may have lost the 24vdc or the backlight inverter board may have shorted out, you need to do in-depth troubleshooting.
If you are going to DIY and have proper tools, electronics knowledge, and know safety precaution then please read on:

Please see my basic troubleshooting guide here:
http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide

http://s807.photobucket.com/home/budm/allalbums

http://en.wikipedia.org/wiki/Capacitor_plague

Parts: www.shopjimmy.com
Capacitors kit: http://lcdalternatives.auctivacommerce.com/Default.aspx
8/3/2010 3:07:52 AM • Maxent MX-26X3... • 92 views • 0 helpful votes
1helpful
1answer

Picture is perfect for a short time and then goes fuzzy

Hi,
Let me know model and brand of your tv, these info will be written at rear of tv to diagnose problem and to suggest possible solution.
Thanks.
5/18/2010 8:36:07 PM • Maxent MX-26X3... • 204 views • 1 helpful votes
1helpful
1answer

Power cable one connector was melting and now tv

firstly any sign of melting on power wires should indicate DANGER and FIRE Do not attempt to use this appliance or handle the cord while it is plugged to the power. Take it or call in an electrical technician or replace the whole cord for safety. He can also check for any short circuits that may have caused the fault in the first place.
Please rate my help++++Thanks for using FIXYA
5/12/2010 1:21:22 AM • Maxent MX-26X3... • 113 views • 1 helpful votes
0helpful
1answer

Only lines show

Check the back cable. It may be loose or broken connector.
2/24/2010 2:59:54 AM • Maxent MX-26X3... • 240 views • 0 helpful votes
2helpful
1answer

Fine lines all through my lcd tv

your Lcd panel has failed you will need a new panel but that company no longer in around how ever if you get the genaric number off the panel which is on a white sticker on the back of the panel best bet is take a picture of the sticker then do a google search
hope you get lucky
12/18/2009 12:32:44 AM • Maxent MX-26X3... • 515 views • 2 helpful votes
0helpful
1answer

No picture but sound

this is a lamp problem if you have no picture but you have sound this will be a lamp issue need to replace it
1/17/2010 9:31:35 PM • Maxent MX-26X3... • 208 views • 0 helpful votes
1helpful
1answer

What website can i go on to look for a part for a

rayas en la pantalla y cuando golpeo el tv se arregla
12/5/2009 4:48:49 PM • Maxent MX-26X3... • 315 views • 1 helpful votes
1helpful
1answer

As soon as this plug the power cable and change

(Main Pcb) Part Number is (DPWB11497-ML-B) Price at Encompass Parts is $356.00 core refund for old one is 50.00 Part then is $306.00
and Company has these on Back order Do not have any in stock at this Time 1-800-638-3328 You can Try UED 1-80-648-6657 and You also can Go to E-Bay Look Under Electronic Parts I gave you Part Number so go by that you might even find it alot cheaper on E-Bay.
12/10/2009 6:52:58 AM • Maxent MX-26X3... • 171 views • 1 helpful votes
1helpful
2answers

50" Maxent Plasma

you need to have a licenced repair tech come look at it sounds like the inverter is going out its kinda likea ballast for florecent lights
10/28/2009 7:00:19 PM • Maxent MX-26X3... • 508 views • 1 helpful votes
0helpful
1answer

There i s no picture just sound

There are two places to look for the problems, the backlight inverter board and the power supply. Look at the power supply first since it is easier to get to, look for burnt parts, bad capacitors, etc.
http://en.wikipedia.org/wiki/Capacitor_plague
Please post back what you find.
11/14/2009 6:23:48 PM • Maxent MX-26X3... • 187 views • 0 helpful votes
Not finding what you are looking for?
Televison & Video Logo

58 questions posted

Ask a Question

Usually answered in minutes!

Top Maxent Televison & Video Experts

Grand Canyon Tech
Grand Canyon Tech

Level 3 Expert

3867 Answers

Kolbrun...

Level 3 Expert

1228 Answers

Cindy Wells

Level 3 Expert

6688 Answers

Are you a Maxent Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Maxent Televison & Video

  • Maxent Televison & Video

Most Popular Question

maxent mx 26x3 video issue

  • Televison & Video
Loading...