Hyundai ImageQuest HP4240 42 in. Plasma Television - Page 4 - Answered Questions & Fixed issues

Tu unlock the keypad lock, you should have a remote control. If you wish to buy its original remote control, contact the authorized service centre, or authorized dealer to your device brand. They can either give you a genuine remote control to your device, or can direct you, from where can you purchase a suitable one. To select a proper universal remote control, you should know about the number of digits to its set-up codes. There are 3 digit, 4 digit, 5 digit, 2 digit and even single digit codes, to some brand devices. After confirming this, check the sites linked here. Both the sites have set-up code list and set-up procedure to many popular brand remote controls. Check which brand remote control has set-up code/s to your device brand, and buy that one according to availability? Brand name of the remote control isn't a matter, but it should have set-up codes in its code list, to the device brand you have. Please note: Every new universal remote control will have set-up code list, and set-up procedure along with its pack. Never accept a remote control, that hasn't both of this. For more details about the set-up codes, visit the site http://electrohelponline.blogspot.com/ Check this site too. http://remotesearch.blogspot.com/ Universal remote controls are available at most of the electronic spare part selling shops.

Cabinet rattling. Contact any service technician to fix any loose fitted screws or any.

i think ur t v not support hdmi high resolution it set 768 work properly

You may need the power supply capacitors. You can identify the bad ones by their bulging tops. If you have the wherewithal, they can be replaced for about $10.00 or less.

May need power supply capacitors. you can identify the bad ones by their bulging tops. If you have the wherewithal, you can replace them for about $10.00 or less.

Some component could be defective. The symptom is so vague it could be a million things. Take it to a tv repair shop.

Check and replace its main power regulator board inside. If you are not familiar with electronics, do not attempt to repair. Whether you suffer fatal electric shock. Instead, contact any experienced service technician, or the nearest service center.

Some components are getting heated up most probably in the sound section due to high voltage. Either there is a failure of regulated power supply to that are or the IC or other components in the board are defective. This is a case to be handled by a qualified service technician, as the back cover has to be opened.

Yep, I can help but I am afraid that I won't be able to bring totally good news.

The TV is in forced standby also called "protection". Protection kicks in when an internal fault such as a short (big power draw) or a wrong voltage is detected. The click comes from a relay activated by the protection circuit to force TV to shut down.

All you can do is disconnecting the power cord, checking if there is a fuse built in the power cord, replacing fuse and connecting back after about 30 minutes (that allows power drain). If the TV does not work there are faulty internal parts that need replacement.

If now the TV does not start at all, and not even the standby light is on, then the problem is usually the PSU. The part must be tested and eventually replaced.

Here replacement parts for most flat panel TV models:ShopJimmy.

See also: PartStore

Regards.

Ginko.

hi;
first try to check power cord if still good,
maybe some capacitor has bloated or changed value, try to watch this http://www.youtube.com if you know how to solder, or even disassemble the back of LCD TV. if not try to call a repair technician. thanks ,, hope this help........

In most cases when the CD does not play it is possible that the optical head is a suspect. Sometimes it might pick up ordinary audio CD but will not play other formats. This indicates that the optical head is weak and so there is no detection or scanning of the CD . If the optical is working the tracks will be read immediately but with no scanning the laser head can be defective.

The main motor will not work in some cases as unless the tracks are read the drive motor will not work with signal from the processor. Also in some cases the central motor base can shift and so the distance to the disc can be more resulting in low detection. You can pull up the spindle to come closer. Sometimes certain cleaner disks will not be tracked to run for cleaning as it will not be read and so will reject. Hence it is ideal to manually clean the laser head eye using a cleaning swap /cotton bud with gentle pressure on the lens eye.If there is no result then watch if the CD spins or tries to spin. If so the board seems to work unless a test is taken on the main board but the possibility of a defective optical head can be the suspected fault.If any of the above seems otherwise we must recheck with possibilities of a malfunction of the main processor board

The plasma screen is literally burned down - used up, worn out, whatever you want to call it. This is a sign that the screen is near death due to its age and not a defect. There is nothing that can be done to save it, the tv is dying.
Time for a new one.

The surge may have scramble the mother board, try unplugging it for about an hour to let it reset itself, if that does not work, then you may need to replace the main board.

If you are going to DIY and have proper tools, electronics knowledge, and know safety precaution then please read on: Basic LCD monitor and TV troubleshooting guide: http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting http://www.fixya.com/support/r7406380-tv_training_manuals Failed TV and Monitors pictures: http://s807.photobucket.com/albums/yy352/budm Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague Parts: www.shopjimmy.com Parts: www.interliquidparts.com Capacitors kit: http://lcdalternatives.auctivacommerce.com/Default.aspx he can make you a set of caps. Or www.digikey.com, just make sure to use caps with low ESR, 105c, high ripple current and long life rating such as PANASONIC FM or FC series.

HYUNDAI HU-TV2121 processor N403 KALORA HHEN16MD01.Videoprotsesor LA76810A - the very bottom hidden button (right of the circuit), click once highlighted FACTORY. More P + and P-switching options.

HYUNDAI C2910, C2519, C2988
1. Set the volume -0
2. Press the remote button "MUTE"
3. While holding "MUTE", press "MENU" on the front of the TV.
4. On the top right corner will light up the letter "D", and in the left corner shows an adjustable parameter and its value.
5. Pages menu change button "CAL"
Switching parameters conducted green and red buttons on a blue field panel. Change made a yellow and blue buttons on a blue field.

HYUNDAI H-LCD2000
To enter service mode simultaneously press "MENU" and "STANDBY".
Press "MENU" again.

HYUNDAI, ITT 29M03 C2131 chassis CPU M37160M8-064FP
In the main menu code 6, 4, 8, 3.
Tools submenu contains the switch to the next of which is done by putting 6, 4, 8, 3.

HYUNDAI 359, 387, 8FHIFI, CB5373Z, 6578F processor CCU SEL04 / SEL07A
Mode 1: Close contact in the hole near the keyboard and just press "S"
Mode 2: Close contact in the hole near the keyboard and just press "S" again and click on contact. Exodus - LOAD.

HYUNDAI processor SAA1293-03-03 SAA1293A
With remote control TV "Horizon" graphics without clicking "SERVICE", the indicator shows a CH, a paz-click on 'appears OP, then choose the volume of registers numbers "1-4" and numbers "1-9" change bits. Then click on "Memory" (you can also lock the pins 15 and 23 in the control circuit SAA1250). Exodus - POWER OFF.

HYUNDAI chassis CCU11 - "•?" (C) (H)
Chassis CCU12 - close contact in the hole near the keyboard and just press "S". Exodus - LOAD.

HYUNDAI chassis M1, ITT, NOKIA, SALORA 6390, 7190, MV4000, PL14 24 101 852 SAT SOLI, 882 SAT SOLI, 885 SAT SOLI processor CCU-SALO-07 (CCU20XX)
entrance "C"> "*"> "O / V"> "#"> "M". Exodus - "power".

HYUNDAI chassis EUROSTEREO-1. DIGIVISION 1963 .. 2, 1971 .. 2, 2 .. N6 processor NES3-... NES2-..
Log "-/--" "MENU" "TV" - for a second. Exodus - POWER OFF.

HYUNDAI chassis STEREO PLUS. 5575SFN, 28T7 processor ST92T93
Entrance - "i" "M" "P +", output - TV.

HYUNDAI 3875EX DIGIVISION
Gun "AV7 universal" fully fit.
Sign in service "1-/11. (Button with painted upper corner). TV must be turned on and display a feed.
Recommended initial value: V.AMP-027. V.LIN-038. S.COR-020. V.POS-023. H.POS-041.H.AMP-022. P.TILT-013. P.AMP-024. P.CORN-007. GREEN-032. RED-032. BLUE-032. V.BRE-005. LUM.DEL-000. AUDIO-032.OPBYT1-002. OPBYT2-064. OPBYT3-000. PRLOSK-000. RESERVE-000. Writing in memory - click "E".
Memory 24c08 can put a clean, turn on TV it propyshe processor itself.

from electronics-planet .blogspot

I was told it is the deflector curcits, HOT, Horizontal IC

Please try 0863 for Hyundai Televisions To program your Sky remote control using the 4 digit code

1. Switch on the TV set
2. Press the TV button on the Sky Remote
3. Hold down the Select and Red buttons for 2-3 seconds until the LED blinks twice
4. Press the TV button on the Sky Remote again
5. Enter 0863
6. The LED should blink twice, if not recheck the 4 digit code used and go back to 1
7. Press the standby button on the Sky Remote (The TV should go to standby)
8. Press the Select button to store

If the TV does not go into standby press the TV button then the standby button, then TV then standby, keep repeating this until successful. This will scan the codes used for a particular make of TV.

Please keep me posted.

Thanks.

Lor04

first thing is the obvious, make sure you have brand new batteries installed. If you have a camcorder or digital camera, point it at the remote control and push record, while recording, press some of the buttons on the remote. the camera will record the red light if the remote is working (camcorders and digital cameras can see this light even though people can't) to do this with your digital camera, have somene push and hold one of the remote control buttons while you take a photo, the red ligth should show up in the photo. If you see no red light then you have a bad remote control and will need to send for one or get one ordered through the store, one other option is to buy a universal remote control and try getting that to work, good luck

If this set is under warranty you should return it to get it repaired/replaced by the seller. IF YOU KNOW HOW TO WORK WITH ELECTRONICS REPAIR(board replacement) or have a friend with knowledge/skill you can fix it. With the set on place a bright flashlight again the screen. Look for a moving image around the edge of the flashlight. This will show an image is getting to the screen. You just need a back light to see it. The back light inverter board needs to be replaced. This is the board that controls power to the fluorescent lamps that light the screen. Since you did not give a make and model of the set I can not give more information.

the source, future shop, dollar store, londen drugs, wall Mart all have universal remotes, and will likely have one that will work with your brand of TV

Your best bet is likely to be Amazon.
If you can't find the specific one for your player they do sell a variety of 'universal' in car chargers for all sorts of electronic devices with a selection of inter-changeable end connectors to suit your equipment.
The charger socket on your player should have a symbol on it to indicate polarity (whether the pin or sleeve is positive or negative) it should also show the correct voltage required - check that any charger you buy covers that voltage range.