20 Most Recent Panasonic SR-CG05NW 3-Cup Rice Cooker - Page 8 Questions & Answers

Hold down the start button till the display goes blank again.

Hi, iadded the flour yeast and water and set the controls for my panasonic SD250 but nothing happens

1. http://www.manualsonline.com/ex/thread/view/idThread/2307402 or
2. http://safemanuals.com/user-guide-instructions-owner-manual/PANASONIC/SD-251-_E

Thank you for using FixYa. The error code H43 refers to an internal water leak. The leak is obviously only a small one or you would have noticed. A small amount of water on a sensor will bring up the error code. A simple solution is- remove the back of the machine after first un plugging it from the electricity and dry up any water then try again.

I hope this has been of some use and would appreciate your "helpfull post" if it has

Thank you

http://service.us.panasonic.com/OPERMANPDF/SDYD250.PDF

All I could find close to that was this model, the SDYD 250.

Please confirm the model number on yours and where the unit was purchased (what country).

Please comment back here to this page and I will try to assist you further.

Thank you.

take a look at your manual and find how long the last knead takes for the program you are choosing. Then, just open the lid and pour in your add-in when there is 7 minutes left on the last knead cycle, close the lid and your add-ins will mix in. without being over mixed.

Hi,

Here is a tip that I wrote that will help you with using your rice cooker to steam your veggies...

How to Steam Vegetables in your Rice Cooker

heatman101

';';';';';';';';';';';';';';';';

These motors are usually small geared motors. You will have difficulty truning it manually because if the high gearing. The motor could be defective and need replacing. You should be able to access it from under the appliance.

Could your yeast be stale? It gets stale very quickly once opened. i tend to use sachets to avoid this.
Could the yeast be coming into contct with the liquids too soon. Keep yeast away from fats and liquids. Put it in first for most Panasonic machines, then the flour which keeps it dry till machine starts to knead.
You also must use strong bread flour not all purpose. good luck

If the bread maker still works, means that you had a temporary power outage. You can naturally bake it in the oven, but you will have to allow time for the yeast to activate and rise the dough to approximately double size than the starting dough. You can use a cooking pot full of warm (120-135f) and have the dough seating over it (in the pan that you will bake it in).Cover the whole thing (water and dough)with terry cloth towel for minimum of 45 minutes and bake it in a pre-heated oven (425f). Avoid any drafts durring the rising of the dough.

No you need to let your machine cool off about 20-30 minutes before baking another loaf otherwise your yeast in the 2nd loaf could be negatively effected by the residual heat.

Hi,
You should be able to find what you need here

heatman101

Hi,

You can download and print the instruction manual in PDF format by clicking this link.

On the page which opens, click on the "Download" button to download and save the manual.

Please note: Adobe PDF Reader is required to view this manual. Download Adobe Reader

Hope this solves your problem. Kindly let me know if you have any difficulty in downloading the manual.

Thanks for using FixYa.

to install your scanner into the computer,connect the scanner USB to computer usb input. insert the installation disk( that comes with your scanner package)into the CD rom drives the computer will now the installation wizard then just follow the instruction given by the wizard..good luck

Hi,

You can download and print the instruction manual in PDF format by clicking this link.

Adobe PDF Reader is required to view this manual. Download Adobe Reader

Hope this helps. Thanks for using FixYa.

This is a tough one. One thing you might try until you can replace your machine is to look in your manual and look at the page that shows the cycles of the program you chose. I wonder if you could shut the machine down after the last rise cycle next time,,,,,the,,,,. Push the Stop button until it beeps.... then unplug your machine and reprogram your breadmaker on the "Bake" program and set the time by pushing the timer advance button in 10 minute increments to the equivalent of the last bake cycle of your original program for light crust bread? That just might work!