How do i change right headlight bulb on a 2007 hyundai tucson

There is no fuse for the interior lights. It is likely to be the bulb or the door switch.

The second Page link shows locations.

2005 Hyundai Tucson fuse box diagram

StartMyCar https://www.startmycar.com > Tucson > Fuse box

2005 Hyundai Tucson fuse box diagram. The 2005 Hyundai Tucson has 2 different fuse boxes: Engine Compartment diagram. Inner Panel diagram.

Hyundai Tucson (JM; 2004-2009) fuses and relays

Fuse Box Diagrams https://fuse-box.info > hyundai > hyundai-tucson-jm-2...

Here you will find fuse box diagrams of Hyundai Tucson 2004, 2005, 2006, 2007, 2008 and 2009, get information about the location of the fuse panels inside ...

You've visited this page 2 times. Last visit: 2023-08-01

Hyundai Tucson 1 (ix35) - fuse and relay

FuseAndRelay.com https://fuseandrelay.com > hyundai > tucson-1

It is located in the left end of the dashboard, behind the protective cover. ... The fuses designated as C / LIGHTER or P / OUTLET are responsible for the ...

You visited this page on 2023-08-01.

..

Cut the bolt and fit new bolt the other way round

You have to take the black plastic top off under the hood on the front.....than you take the whole headlight out, I believe it's only two bolts...there is opening for each light and they are pretty simple to change.

Yes the lights are seperately fused.

I suppose my clarification was more of a possible solution. Looking for other thoughts or ideas as well. I can live without the high beams. I can't live without my low beams!

Have your voltage checked. This is usually done with an alternator test at a local autoparts store. If that checks out look closely at the mounts for the headlight and make sure its not loose. Vibration can cause bulbs to blow. Make sure there is no moisture in the lens. Water will cause it to blow.. Lastly when you replace the bulb do not touch the glass. The oil from your skin will cause it to blow early.

check alternator output ,if its higher than 14.7 volts change it

Open hood, reach behind headlight. If necessary remove battery and coolant overflow tank.
Then reach in behind headlight. There will be a plastic ring on back of headlight. Turn counter clockwise and pull back and slide back out of the way. Then grab the headlight bulb, turn counter-clockwise and pull back to remove. Then unclip the wire harness from the bulb itself and reverse procedure to replace.

on each headlamp assembly, there will be either one or two plastic nuts that you can turn.

If you only have one nut on each, that will adjust the vertical aim of the headlights.

If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

hi there
the solution is simple,
you only need to undo the screw on top of the side light/indicator. then facing the head light place a flat headed screw driver under the bottom lip of side light. the bottom of the lihgt is on a small push fit stud, use a sponge or cloth to protect your bumper paint work then just apply pressure gently to lever side light out towards you, It will come dont worry, you may then change your bulbs if you wish remove the whole light unit you will see the bottom bolt as soon as you release the side light. to replace just push back into place then replace screw. whole job takes about five minutes

hope this helps kevan hildred