I am changing the blower motor for the heater and can not get the blower out of the housing

Here's a picture of it,located next to blower motor,2 screws hold it on.Here's where the blower motor is.

Check this procedure...Blower Motor Resistor and Controller Replacement


REMOVAL

1. Disconnect and isolate the batten' negative cable.

2. Depress locking tab and unplug the wire harness connector from the blower motor

resistor or controller (power module).

3. Depress locking tab and unplug the resistor or controller connector from the blower

motor.

4. Remove the 2 screws that secure the blower motor resistor or controller to the

heater-AC housing.

5. Remove the blower motor resistor or controller from the heater AC housing.


INSTALLATION

1. Install the blower motor resistor or controller to the heater AC housing. The

housing is indexed to allow (controller power module) mounting in only one

position. Tighten the mounting screws to 2.2 Nm(20 in. Lbs.).

2. Plug in the wire harness connector to the blower motor resistor or controller.

3. Plug in the connector from the blower motor resistor or controller to the blower

motor.

4. Connect the batten' negative cable.




Hope this helps (rerember to rating this and leave a testiomonial).

either have a fuse blown, or you need a resistor pack. it's located in the heater box next to the blower motor.

Welcome to FIxYa.com

Blower Motor Resistor and Controller Replacement

Image Blower Motor Resistor Or Controller/Power Module Remove/Install

REMOVAL

1. Disconnect and isolate the batten' negative cable.

2. Depress locking tab and unplug the wire harness connector from the blower motor

resistor or controller (power module).

3. Depress locking tab and unplug the resistor or controller connector from the blower

motor.

4. Remove the 2 screws that secure the blower motor resistor or controller to the

heater-AC housing.

5. Remove the blower motor resistor or controller from the heater AC housing.

INSTALLATION

1. Install the blower motor resistor or controller to the heater AC housing. The

housing is indexed to allow (controller power module) mounting in only one

position. Tighten the mounting screws to 2.2 Nm(20 in. Lbs.).

2. Plug in the wire harness connector to the blower motor resistor or controller.

3. Plug in the connector from the blower motor resistor or controller to the blower

motor.

4. Connect the batten' negative cable.

Thank you for using FixYa.com

Regards, Lee Davidian

It will be up under the dash on the passenger side near the blower motor. It will have 5 or six wires in its connector

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

it's behind the glove box. here are procedures from autozone.com:

CAUTION The Supplemental Inflatable Restraint (SIR) system must be disarmed before removing the blower motor assembly. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.

• Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.

Remove the glove box from the instrument panel.

Fig. The blower motor is located behind the glovebox, behind the blower motor cover

• Remove the A/C-heater blower motor cover.
• Disconnect the blower motor wiring connector.
• Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.

Remove the blower motor mounting screws.

Fig. Once the cover is removed, unplug the electrical connector and push it through the opening in the housing

Fig. The blower motor is secured to the housing with three small screws

Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.

To install:

1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
3. Reconnect the blower motor electrical connector.
4. Install the A/C-heater blower motor cover.
5. Install the glove box into the instrument panel.
6. Reconnect the negative battery cable. Check blower motor operation.

Removal

1. Remove the glove compartment liner to gain access to the heater blower motor and blower motor wheel assembly mounting screws.
   

1. Use a small screwdriver to remove clip retaining hydraulic damper strut.
   

1. Remove four screws and remove the heater blower motor assembly and blower motor wheel assembly from the heater blower motor housing.
   

Installation

1. Using a new seal, position the heater blower motor and blower motor wheel assembly to the heater blower motor housing with the flat side of the flange near the heater blower motor switch resistor (18591). Install the four retaining screws.
   

1. Tape the heater blower motor power lead to the air inlet duct to keep the wire away from the blower outlet during installation.
   

1. Install the heater blower motor and blower motor wheel assembly in the vehicle.
   

1. Install the glove compartment liner.
   

No, but it isn't too hard to get to under dash. I will paste instructions from autozone.com below. Pictures may not come thru.

CAUTION The Supplemental Inflatable Restraint (SIR) system must be disarmed before removing the blower motor assembly. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.
Front Blower Motor
See Figures 1, 2 and 3

Fig. Fig. 1: The blower motor is located behind the glovebox, behind the blower motor cover

1. Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
2. Remove the glove box from the instrument panel.
3. Remove the A/C-heater blower motor cover.
4. Disconnect the blower motor wiring connector.
5. Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
6. Remove the blower motor mounting screws.

Fig. Fig. 2: Once the cover is removed, unplug the electrical connector and push it through the opening in the housing

Fig. Fig. 3: The blower motor is secured to the housing with three small screws

1. Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.

To install:

1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
3. Reconnect the blower motor electrical connector.
4. Install the A/C-heater blower motor cover.
5. Install the glove box into the instrument panel.
6. Reconnect the negative battery cable. Check blower motor operation.

Removal & Installation




The blower motor is located behind the glovebox, behind the blower motor cover

1. Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
   
2. Remove the glove box from the instrument panel.
   
3. Remove the A/C-heater blower motor cover.
   
4. Disconnect the blower motor wiring connector.
   
5. Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
   
6. Remove the blower motor mounting screws.
   

Once the cover is removed, unplug the electrical connector and push it through the opening in the housing



The blower motor is secured to the housing with three small screws

1. Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.
   

To install:

1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
   
2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
   
3. Reconnect the blower motor electrical connector.
   
4. Install the A/C-heater blower motor cover.
   
5. Install the glove box into the instrument panel.
   
6. Reconnect the negative battery cable. Check blower motor operation.
   

Please don"t forget to rate:

Removal & Installation
CAUTION The Supplemental Inflatable Restraint (SIR) system must be disarmed before removing the blower motor assembly. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.

1. Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
   
2. Remove the glove box from the instrument panel.
   

The blower motor is located behind the glovebox, behind the blower motor cover

1. Remove the A/C-heater blower motor cover.
   
2. Disconnect the blower motor wiring connector.
   
3. Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
   
4. Remove the blower motor mounting screws.
   

Once the cover is removed, unplug the electrical connector and push it through the opening in the housing


The blower motor is secured to the housing with three small screws

1. Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.
   

To install:

1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
   
2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
   
3. Reconnect the blower motor electrical connector.
   
4. Install the A/C-heater blower motor cover.
   
5. Install the glove box into the instrument panel.
   
6. Reconnect the negative battery cable. Check blower motor operation.