SOURCE: Cylinderhead bolts torque settings
According to my haynes manual for Landrover 200tdi, G - S reg,1989-1998 it goes as follows,
Stage 1:- Tighten all bolts to 30lb ft or 40Nm then
Stage 2:- Angle tighten a further 60 degrees then
Stage 3:- Angle tighten a further 60 degrees again.
SOURCE: head bolts torque settings
According to my haynes manual for G-S reg, 1989-1998 it goes as follows,
Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head.
Stage 2:-Tighten all bolts to 40Nm or 30lb ft.
Stage 3:-Angle tighten all bolts a further 60 degrees.
Stage 4:-Angle tighten all bolts again a further 60 degrees.
Stage 5:- M12 x 140mm bolts ONLY angle tighten a further 20 degrees.
Hope this helps everyone, sorry it seems longwinded but that is how it's written in the manual.
SOURCE: require ford escort rs 2000 1976 torque settings head bolts
2lt overhead cam with them horrible tappet adjusters,cast iron head but valves dont hit the head if the timing belt breaks ,but it does on the 1600 .called a pinto in america .Remember the assembly line well ,have many a fond memory of working on it and the staff canteen on night shift ,what lovely grub we got.Head bolt torque is about 80lbs because i used to pull them down to check them after the machine had tightened them up
SOURCE: head bolt torque settings for 720 nissan cab 2
dear friend-your torque setting on the 720 is the same as the L18 and is set at 85 - 90 nm.
SOURCE: mitsubishi canter truck 4d34 torque settings
Hi!!!
Most manuals I found do not cover diesel engines. There is a Peter Russek manual for your truck which covers diesel engines. Click on the following link to check the manual
http://www.auto-repair-manuals.com/Mitsubishi-1997-2002-L200-2WD-4WD-2-0L_2-4L-Petrol-2-5L-Diesel-Russek-Repair-Manual.html
THIS ARE THE SPECS FOR A 04 MITSUBISHI LANCER.
Identifying Fastener Tightening Specifications Table
ITEMS SPECIFICATIONS
Roll stopper bracket mounting bolt69 ± 10 N.m (51 ± 7 ft-lb)
Shift cable bracket mounting bolt19 ± 3 N.m (14 ± 2 ft-lb)
Select lever mounting bolt19 ± 3 N.m (14 ± 2 ft-lb)
Speedometer gear mounting bolt4.0 ± 1.0 N.m (35 ± 9 in-lb)
Backup light switch32 ± 2 N.m (24 ± 1 ft-lb)
Interlock plate bolt30 ± 3 N.m (22 ± 2 ft-lb)
Poppet spring32 ± 2 N.m (24 ± 1 ft-lb)
Control housing mounting bolt19 ± 3 N.m (14 ± 2 ft-lb)
Under cover mounting bolt7.0 ± 1.0 N.m (61 ± 9 in-lb)
Reverse idler gear shaft mounting bolt48 ± 6 N.m (35 ± 4 ft-lb)
Clutch housing-transaxle case mounting bolt44 ± 5 N.m (33 ± 4 ft-lb)
Front bearing retainer mounting bolt19 ± 3 N.m (14 ± 2 ft-lb)
Select lever mounting nut12 ± 1 N.m (104 ± 9 in-lb)
Stopper bracket mounting bolt22.3 ± 0.3 N.m (16.1 ± 0.2 ft-lb)
Clutch release bearing retainer mounting bolt9.8 ± 2 N.m (87 ± 17 in-lb)
Differential drive gear mounting bolt132 ± 5 N.m (98 ± 4 ft-lb)
352 views
Usually answered in minutes!
×