Car is locked up & won't do anything
Try changing the battery inside the remote usually that solves the problem but otherwise u might also have broken or loose parts inside the remote from dropping it on the ground,or rubber gasket maybe in in perfectly, if none of those solutions work, it may need to be reprogrammed or replaced,from the dealership.
usually its the coin cell battery eg:2016,2032,etc
and u'll need a small flat precision screwdriver and some patience when opening it.
SOURCE: remote keyless entry
“CUSTOMER LEARN” MODE
This feature is only available on domestic vehicles or those which have a U.S. country code designator. This procedure requires access to at least two valid Sentry Keys. If two valid Sentry Keys are not available, Sentry Key programming will require the use of a scan tool.
The steps required to program Sentry Keys with two valid Sentry Keys follows:
1.
Obtain the blank Sentry Key(s) that need to be programmed. Cut the keys to match the ignition lock cylinder mechanical key codes.
2.
Insert one of the two valid Sentry Keys into the ignition switch and turn the ignition switch to the ON position.
3.
After the ignition switch has been in the ON position for longer than three seconds, but no more than fifteen seconds, cycle the ignition switch back to the OFF position. Replace the first valid Sentry Key in the ignition lock cylinder with the second valid Sentry Key and turn the ignition switch back to the ON position. The second valid Sentry Key must be inserted within 15 seconds of removing the first valid Sentry key.
4.
About ten seconds after the completion of Step #3 , the indicator light will start to flash and a single audible chime tone will sound to indicate that the system has entered the "Customer Learn" programming mode.
5.
Within sixty seconds of entering the "Customer Learn" programming mode, turn the ignition switch to the OFF position, replace the valid Sentry Key with a blank Sentry Key transponder, and turn the ignition switch back to the ON position.
6.
About ten seconds after the completion of Step #5 , a single audible chime tone will sound and the indicator light will stop flashing and stay on solid for three seconds and then turn off to indicate that the blank Sentry Key has been successfully programmed. The SKREES will immediately exit the "Customer Learn" programming mode and the vehicle may be started using the newly programmed Sentry Key.
NOTE:
The Remote Keyless Entry (RKE) Transmitter will also be programmed during this procedure.
These steps must be completed in their entirety for each additional Sentry Key to be programmed. If any of the above steps are not completed in the given sequence, or within the allotted time, the SKREES will exit the "Customer Learn" programming mode and the programming will be unsuccessful. The SKREES will also automatically exit the "Customer Learn" programming mode if:
NOTE:
If you attempt to start the vehicle while in “Customer Learn” mode (LED flashing), the vehicle will behave as though an invalid key is being used (i.e. the engine will stall after two (2) seconds of running). No faults will be logged.
NOTE:
Once a Sentry Key has been programmed to a particular vehicle, it cannot be used on any other vehicle.
SOURCE: were is the fuse box in a dodge grand caravan 2003?
i have a 2002 caravan and the turnsiginals are only working inside the dash nothing outside has new bulbs and still nothing anyone any ideas?
SOURCE: 2003 dodge grand caravan ac recharge
you should be adding the 134a to the system the low pressure switch is doing its job by not allowing the compressor to kick on, it wont kick on until there is enough 134a in the system to be above the preset pressure for the low pressure switch.
SOURCE: NEEED FUSE FUSE BOX LAYOUT FOR 2003 DODGE GRAND CARAVAN
You can get free owners manuals online at:
http://www.edmunds.com/ownership/howto/articles/120189/article.html
or just type "owners manuals" in your search.
Here is a post I found that worked for my 2005 caravan.
For a
2001 Dodge Caravan: The owner's manual is vague, only stating that all
fuses are under the hood in the fuse box, no diagrams. Once you have
removed the fusebox cover, the diagrams for what each fuse does is
provided under the lid. UNCLEARLY marked is the radio fuse, a 20amp
fuse located 2nd row from top to the right of the accessory relay. It
is marked: RDO/IP IGN.
Jake
234 views
Usually answered in minutes!
I meant to say the rubber gasket may not be in perfectly, sorry about the misunderstanding if any caused.
×