Question about 2000 Nissan Maxima

1 Answer

Seat Belt repair/replace

I can't figure out how to remove the housing that covers the seatbelt without damaging it. Can you help

Posted by msgt on

Add Your Answer
  • Anonymous Mar 16, 2014

    have seat covers i want to install i need to remove the seat belts to do so..

×

Ad

1 Answer

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points
    MVP:

    An expert that got 5 achievements.
    Sergeant:

    An expert that has over 500 points.
    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 150 Answers

  1. Remove front seat.
  2. Remove adjuster cover. A
  3. Slide floor anchor cover.
  4. Remove floor anchor bolt. B
  5. Remove shoulder anchor bolt. C
  6. Remove front and rear kicking plate, then remove center pillar upper and lower garnish.
  7. Disconnect seat belt pre-tensioner connector.
  8. Remove the screw securing seat belt pre-tensioner retractor, then remove seat belt and seat belt pre-tensioner retractor.
  9. Remove bolts securing seat belt adjuster, then remove seat belt adjuster. Reverse procedure to install.J

Posted on Nov 03, 2008

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to replace the left rear seatbelt in my VW Jetta my10, how do I go about it?
all the jetta rear seats and seat belt parts
look the same sort of set up

fiddly job
back seat section or sections out
have to remove some plastics
to get to the retractable part of the belt ....looks like it is
under or mounted on the rear parcel shelf
undo the floor mount

then re thread and bolt the new seat belt in (pictured)

then replace the seats

26227982-baaqz4pc4guywvkqfm2wgc1t-4-0.jpg

26227982-baaqz4pc4guywvkqfm2wgc1t-4-1.jpg

Jun 29, 2016 | Volkswagen Jetta Cars & Trucks

1 Answer

T Belt light stays on how do I turn it off
If you meant seat belt light, are you driving with your seat belt or without? If with, inspect the wiring that goes into the bottom side of the seat belt receiver for pinched/damaged wires. If you are not using a seatbelt (not advising this, but your choice) you can get replacement buckles that will clip in just like your seatbelt does, our you could grab some off same model vehicle in a salvage yard.

Aug 20, 2014 | Cars & Trucks

2 Answers

Hi, I would like to know if the front seat belt retractors for Honda CRV 2003 are the same? If yes, is it difficult to replace the seat belt assembly? I'm planning to buy a used front passenger side...
I don't know if this is something you want to get into? You decide. Front Seat Belt Replacement SRS components are located in this area. Review the SRS component locations and the precautions and procedures before performing repairs or service.
NOTE: Check the front seat belts for damage, and replace them if necessary.

Front Seat Belt

  1. Make sure you have the anti-theft code for the radio, and then write down the frequencies for the preset buttons.
  2. Disconnect the negative cable from the battery, and wait at least 3 minutes before beginning work.
  3. Slide the front seat forward fully.
  1. Pull the lower anchor cover (A) back, and remove the lower anchor bolt (B).
  2. Remove the B-pillar lower trim panel.

  1. Remove the upper anchor cover (A), and remove the upper anchor bolt (B).

  1. Disconnect the seat belt tensioner connector (A), and detach the harness clip (B) from the retractor (C). Remove the upper retractor mounting bolt (D), and the lower retractor bolt (E), then remove the front seat belt (F) and retractor.
  2. If necessary, remove the front seat belt protector (G).
  3. Remove the B-pillar upper trim.

  1. Remove the shoulder anchor adjuster (A).

  1. Install the seat belt in the reverse order of removal, and note these items:
    • Assemble the washers, collar, and bushing on the upper and lower anchor bolts as shown.
    • Check that the retractor locking mechanism functions.
    • Apply liquid thread lock to the anchor bolts before reinstallation.
    • If the seat belt tensioner has been activated, replace the front seat belt protector with a new one.
    • Before installing the anchor bolts, make sure there are no twists or kinks in the seat belt.
    • Make sure the seat belt tensioner connector is plugged in properly.
    • Reconnect the negative cable to the battery.
    • Enter the anti-theft code for the radio, and then enter the customer's radio station presets.
    • Reset the clock.
    • Do the PCM idle learn procedure and the power window control unit reset procedure.
Upper anchor bolt installation
Lower anchor bolt installation

Seat Belt Buckle

  1. Make sure you have the anti-theft code for the radio, and then write down the frequencies for the preset buttons.
  2. Disconnect the negative cable from the battery, and wait at least 3 minutes before beginning work.
  3. Remove the front seat.
  4. If equipped, remove the center table.
  5. Remove the under seat storage box.
  6. Remove the center cover, driver's, passenger's.
  1. Driver's: If equipped with seat heater, remove the harness band (A), and disconnect the seat subharness connector (B). If equipped without seat heater, detach the seat belt switch connector clip (C). Detach the seat belt buckle tensioner clip (D), and harness clip (E).

Dec 11, 2017 | 2003 Honda CR-V

1 Answer

Back seat belt will not retract how do I get into the seat belt housing to fix it? thanks Dave
Dave I highly reccomend you to replace the seatbelt instead of repairing it ...you wouldnt want it to fall in an accident... the dealer dont repair them for this reason

May 05, 2010 | 2001 Toyota Sienna

1 Answer

1991 Honda Accord Ex. My seat belts on both sides (driver's and passenger's) stopped working. I just want to push them back in the position and turn electricity off. How?
You should take it to your Honda dealer for repair. Honda has a lfetime warranty on seatbelts. See below.
While seat belts cannot completely
remove the possibility of injury,
they do provide a very significant
level of protection when used
properly. Honda believes the best
way to enhance your safety is to
use your seat belt. To encourage
their use, the seat belts should
always be in good operating
condition.
Time Period
 This warranty continues for the
useful life of the vehicle.
Warranty Coverage
 Honda will repair or replace, at its
option, any Honda seat belt
component that fails to function
properly during normal use. This
includes all parts and labor
charges.
This Warranty Does Not
Cover:
 • Replacement of a properlyfunctioning
seat belt assembly
strictly for cosmetic or comfort
reasons.
• Failure caused by abuse,
alteration, accidental damage,
misuse, or malfunction resulting
from a collision.

May 03, 2010 | 1991 Honda Accord

1 Answer

Warning light came on this morning, figure of a man with the seatbelt. What does this indicate?
This is the seatbelt indicator, its not seeing that your seatbelt is fastened ifthe light stays on and the chime keeps going off.

There is a switch inthe seatbelt that closes when the seatbelt is buckled, and if not, thelight stays on and the chime goes off.

There are a couple reasons thiscould happen. It could be a wiring issue going to the seatbelt buckle,or more likely the buckle itself. Your truck is pretty new, so if youare under 36,000 miles the repair would normally be covered underwarranty.

Also, I suggest check the Repair Manual for Jeep-WK-Grand-Cherokee-Section-08O-Restraints (page 473 and next, for Seat Belt)

Hope helps with this (remember rated this) Good luck.

Jan 21, 2010 | 2006 Jeep Grand Cherokee

2 Answers

How do you fix a stuck seatbelt in front seat passenger side? The seatbelt has retracted but will not release outwards to enable its use. We have pulled off interior cover of the seatbelt to get access to...
this is a simple repair many dont know. remove or pull off plastic pillar post cover, seatbelt probably twisted inside. twist it back around so it runs flat and lube slightly with a light lube spray on metal gearing. i had the same problem w mine pk

Jan 16, 2010 | 1998 Ford Taurus

1 Answer

Seatbelt won't retract
1)move the plastic cover over the seat belt out of the way to gain access to the two mounting bolts for the seat belt mechanism. Use a 10mm wrench and a 14mm wrench and remove the two bolts holding the seat belt mechanism to the body. Use a small drill bit or small screwdriver and make one hole in the plastic cover on each side of the seat belt mechanism (the covers say "do not remove plastic cover". Spray lots of wd40 in each hole. Then exercise the seat belt. When the mechanism allows the belt to be retracted, retract the belt all the way out and exercise the seat belt. Reinstall mechanism with both mounting screws in original position and put plastic cover back in place. Good luck. New seat belt costs $100.00 from dealer and are hard to find working in junk yards. I have fixed several of them this way.

Jan 17, 2009 | 1996 Toyota Corolla

4 Answers

Volvo V70 rear seatbelt jammed
you can remove the bolt that holds the seatbelt to the floor by pulling off the seatpad where the belt goes to the floor and then raise the seat and the belt should reset. this happens on my passenger side rear seat.

Dec 12, 2008 | 2001 Volvo V70

3 Answers

Rear passenger side seat belt is stuck, and I can't work out how to get to the mechanism without damaging the seat.
If it is a 850 sedan like mine then you'll have to remove the speaker covers and then pull up the rear deck cover, then you can get to the mechanism.

Jul 27, 2008 | 1996 Volvo 850

Not finding what you are looking for?

View Most Popular

2000 Maxima

  • Cars & Trucks

Related Question

I need to replace the left rear seatbelt in my VW Jetta my10, how do I go about it?

  • Volkswagen Jetta Cars & Trucks

Open Questions:

0 Answers

00 nissan maxima 3.0l manual trans, had clutch replaced, now crank, no start issue

Mar 10, 2017 | 2000 Nissan Maxima

0 Answers

2000 NISSAN MAXIMA CUT OFF AND WANT START BACK ALL THE ELECTRICAL CUT OFF

Mar 04, 2017 | 2000 Nissan Maxima

0 Answers

does the rear window come right down for 2000 model NISSAN MAXIMA

Feb 08, 2017 | 2000 Nissan Maxima

0 Answers

I have a boss audio 850 brgb head unit that I cannot seem to get working in my 2000 Nissan Maxima no power any ideas?

Dec 05, 2016 | 2000 Nissan Maxima

See all 2000 Nissan Maxima Questions

Related Topics

2000 Nissan Maxima Logo

4,634 views

Ask a Question

Usually answered in minutes!

Popular Questions

1995 Nissan Maxima

2004 Nissan Maxima

2004 Nissan Maxima

1997 Nissan Maxima

1995 Nissan Maxima

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Nissan Experts

Thomas Perkins
Thomas Perkins

Level 3 Expert

14868 Answers

Greg Bernett
Greg Bernett

Level 3 Expert

2993 Answers

Mike

Level 3 Expert

4376 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
Body Repair Manual. user-manual-2000...

2000 Maxima

PDF Manual
Front & Rear Axle. user-manual-2000...

2000 Maxima

PDF Manual
RESTRAINT SYSTEM. user-manual-2000...

2000 Maxima

Loading...