Where exactly is the inertia switch on a 99 mercury villager

It isn't unknown for both bulbs to fail at the same time. Other possibilities are fuse, switch or wiring.

How to Fix error code P0300 for random misfires on your car ...

diy-auto-repair.wonderhowto.com/.../fix-error-code-p0300-for-random-...

Oct 15, 2010 - How to Fix error code P0300 for random misfires on your car ... amisfire (code P0304) on a 1999 Mercury Villager 3.3L · How to Fix error code P0500 ... I reset my codes and it ran fine for a couple of days, then I started getting ...

(code P0305) on a 1999 Mercury Villager 3.3L - auto repair

diy-auto-repair.wonderhowto.com/.../troubleshoot-misfire-code-p0305-1...

Sep 7, 2010 - The vehicle is a '99 Mercury Village, 3.3L, with 150000 miles on it. The chief ... How to Fix error code P0300 for random misfires on your car ...

2000 Villager Misfire - Car Forums and Automotive Chat ...

www.automotiveforums.com > ... > Mercury > Villager

May 24, 2010 - 2000 Villager Misfire Villager Car Forums. ... i was told that the 3.3L engines of 1999-2002 nissan quests/ mercury villagers are INTERFERENCE engines! ... Hope the following may help, and I will post if my last fix works. ... I have a 1999mercury villager that is showing a random multiple cylinder misfire ...

Rough Idle - 2000 Mercury Villager - RepairPal

repairpal.com > Questions > Mercury > Villager > 2000 Mercury Villager

Repair the code issue, because your Villager has OBD-II which is a very helpful Diagnostic system. Upvote (4) ... My 1999 Villager was running poorly; rough idle, lack of power at highway speeds and the engine problem light indicated random miss-fire, etc. I had new spark ... Have code po306 cylinder 6 misfire detected.

P0301 - OBD-II Trouble Code - RepairPal

Ck power at the inertia switch. In and out.

There should be a spout on the upper fuel rail of the engine. It would look like a valve stem on a tire. There are pressure gauges available through the Tool Loaner programs at places like Autozone,Advance, or Oreilys.

But if you just suspect it is not coming on, then check the Inertia switch and push on it to reactivate the circuit. It is located on the dirver's side above the kickpanel.

Your inertia switch (AKA fuel shut-off switch) is located behind the left side of the dash, above the kick panel (pictured below). You have to manually flip the switch back down to reset it.



I hope this helps you.

make sure you did not accidently hit the lock out switch on driver door controls for windows. Relay is behind fuse panel.

go to villager quest yahoo group for much morehelp

gerry

go to villager quest yahoo group for help.

gerry

I have manuals for sale for $20 plus $5 postage, shop manual plu wiring book.

99-02 essentially the same. villager & quest identical vans.

it is the cam sensor in the distributor. must replace distributor. import experts on ebay $200
very common on 99.

go to villager quest yahoo group for more help. 3000 members free.

gerry

Under hood, driver side, front engine area, rear of headlight housing, front of battery, mounted in fuse/relay block

Check your inertia switch. This is usually located in the rear interior of the vehicle. It has a reset switch you hold for 3 seconds. It is a safety switch to kill the fuelpump in an accident. Can trip with door closings.

p1166 and p1167 are Air/Fuel ratio code sensor codes (O2 sensor codes) heater circuit problem