LG Computers & Internet - Page 2 - Popular Questions, Answers, Tips & Manuals

so working on super old 2007 PC monitors. and no PC connected."? it is NOT ANY LED BACK LAMP monitor here. came new with XP PC's. the monitos all good to sleep mode if no PC vidoeo connected. in the usa, even by law, (energy star) how ever lacking a PC, the screen will show "no signal entering sleep mode" VGA monitor. LED = blue on, amber sleep, LED out, oFF. NO 1080P mode allowed, (so common now) <<<< big clue here. set the PC to 1024 x 768 (to test ) 60Hz. using a flash light (torch) tool,. turn on Monitor, see blue LED point flash light to screen, see data, now, on sceen in the beam now you now CCFL backlamps are dead. as most are this old. Display Modes (Resolution) 640 x 350 720 x 400 640 x 480 800 x 600 832 x 624 1024 x 768 1152 x 870 1152 x 900 1280 x 1024 1440 x 900 proof BELOW. A FREE MANUAL TOO. page 47, see 4, CCFL jacks and HV supplies here 600VDC free service manual with full schematics and BOM https://elektrotanya.com/lg_w1934s_flatron.pdf/download.html in my shop I have VGA signal generator to maKE WORK EASY.

Hi, the typical power button looks like an open circle with a line through the top where the opening of the circle. Usually it's located at the top -right portion of your keyboard. If not there, then please check the sides of your keyboard as well. Thank you.

https://www.youtube.com/watch?v=IHL1wxni7tY

Change your remote battery

ok try this one switch the hard-drive off and on again to restart it and then the screen would come one.

Hello, hope to find you well. You can try the LG ThinQ app for smartphone, that will allow you to control your TV. Hope it helps.

If you get a notice on the screen that the feed is not detected you may want to replace the feed cable to your device. If that doesn't work try the monitor on another device and see if the problem follows.

So the light usually is there to tell you the psu is receiving power...Does pressing any buttons do anything? Can you remove the battery and reseat it?

Several possibilities. Check Bush manual to see if it list compatible formats. All formats are not recognized by all tv's. I am referring to file types. Secondly, check condition of TV ports. Dust may be a problem. Thirdly, TV port may be burnt out. But as you say the drives are recognized, this is more likely your Bush TV does not recognize the file type. You can try converting the file types and see if they then play.

When it first turns on, call up the on screen menu. If it still goes off while using the menu, the monitor has a faulty voltage regulator.

The Desktop Charger is here http://www.ashop.me/p/1024660/genuine-lg-desktop-battery-charger-for-lgip-580a-battery---bc-1650.html and in other outlets. https://www.google.com/search?q=LG+BC-1650+desktop+battery+charger ..

Great answers as always Larry. Why don't you ever put them down here where answers go :>)

Could be a faulty hdd not initializing. Try a new hdd. 500gb is really cheap to buy, you may cosider an upgrade to 1tb perhaps.

I think that the power board and the power supply inside of your TV might be bad and it would be more easier and cheaper to buy a new TV than to try and repair the one that you have that is broken.

This is the best advice and why. https://www.fixya.com/support/r29790007-repairing_own_television ..

Check the all the cables. Check input settings by using the menu.

• Larry Ng Jul 15, 2021that is just a YEAR 2007 LCD computer monitor, it needs a computer to work. if it fails in a 2nd PC , if that test fails,the monitor is bad. (hardward failure, monitor. the tests are simple, it fails on 2nd good PC, what can be more simple that test ANY 14 year old monitor on a 2nd good PC. when dead do this.(test2) they are all here when dead again use a FLASH LIGHT. (or in UK a low carbon foot print TORCH)<< joking. https://pcdied.com/monitors_and_screens/... all monitors older than 2010 do this . (has CCFL inside and that is never fun now) the cure is newer monitors 2011 to now called LED monitor.s or OLED. the tubes are cold cathode florescent tubes. (back lamps.) (have 5 classic fail symptoms not just dead) they are short lived, laptops and monitors both back then. 20,00hours on the clock and go bad. bank on it. the 3 failures are CCFL, PSU board, and logic board #1 is CCFL the all died long ago, on average about year 2003 (07 +5= 12, 2012) at 20,000 yours boom dead. or intermittent. PSU is here: https://pcdied.com/monitors_and_screens/... below is logic board. one of the 3 fail, CCFL tubes dead is like 99% we retire them if the CCFL test fails. (using bench PSU to test them) but you have non of that so. upgrade
• Larry Ng Jul 19, 2021 logic board. (CCFL tubes dead, PSU dead, or logic board dead) and or thermally failing , and bad.
• Anonymous Jul 23, 2021 99% of all monitors are all dead. due to those silly low live CCFL back lamps. or the 2cards inside that can fail too. PSU card +HV CCLF power or the Data card is dead. 99.9% of folks seen these facts, upgrade now. high voltage inside 600v on the CCFL pins

Look here; https://www.youtube.com/results?search_query=lg+x140+disassembly

Hard Reset is the only way. If it was asking for a SIM Lock or PUK Lock, that can only come from your cellular provider. They locked it and only they can unlock. Usually reported stolen :>)

How to unlock LG KC3500 ' sim-unlock.net

sim-unlock.net > simlock > LG > KC3500

How to unlock LG KC3500. How to enter an unlock code in a LG KC3500: First option: 1. Insert a sim card from a different network (for example if the device ...

Unlock LG KC3500 Phone ' Unlock Code - UnlockBase

www.unlockbase.com > unlock-phone > lg > kc3500

If your LG KC3500 comes from MetroPCS USA or T-Mobile USA then it's most likely your Cell Phone is locked with "Device Unlock App" and not asking for a ... Missing: ktf ‎cyon

LG Cyon - Wikipedia

en.wikipedia.org > wiki > LG_Cyon

Cyon is LG Electronics' Korean mobile phone brand. LG established the brand in 1997. Like all other mobile phone brands in Korea, they feature the latest ...

You need to know the old password to change it. If you do not know the password, then there is no way to reset it. You will have to reload the operating system.