How to reset trip meter to zero for every journey on jaguar s type and also where the button to reset is please?

Seems like a complicated button sequence

2008 Aura - Resetting trip meters? - SaturnFans.com Forums

http://www.saturnfans.com > ... > Aura General
Sep. 9, 2014 · 1 post
Press the information button until the outside air temperature along with A or B displays. These modes show the current distance traveled since ...
2007 XR - trip meters
May 8, 2009
Trip Odometer
Mar. 30, 2003
New Speedometer/Odometer Reset
Dec. 20, 2014
Trip Odometer reset
Mar. 20, 2015
More results from www.saturnfans.com

..

To the right (UK)/left(US) and on the dash below the sterring wheel level (near Fog light switch) you will see three buttons A B and Reset. With dash display showing trip millage of the one you wish to reset (A or B) press and hold the reset button for 5 secs.

Vist http://www.bluejag.co.uk for other useful info on your X-type

This is the reset proceedure for a 2008 Highlander with a key-type ignition:

Turn the key ON, do not start the engine.

Look at the odometer, and verify that it displays "TRIP A". If it is on "ODO" or "Trip B", press the black stick next to the odometer to read "TRIP A".

Turn the key OFF.

Press in, and HOLD the black trip meter reset button, hold it IN.
DO not release it.

Turn the key ON, do not start the engine

Observe the Odometer display. You will see 5 dashes, then 4, then 3, then 2, then 1 dash, and finally, 5 zeros. Then, whatever number that was displayed on "TRIP A" will be re-displayed..

Now release the black trip meter reset stick.

This completes the reset procedure, and it will be back on in 5,000 miles, to remind you of you next oil change

Ensure all doors are closed.Turn ignition key to position 1.Press and hold reset button on a dashboard left hand side down/instrument panel/.Immediately turn ign.key to position 2.Keep reset button depresed until trip meter is reset to 0. NOTE:IF trip meter has already been reset.Hold reset button for 10-14 secondsuntil previous trip meter reading is shown.Press and hold reset button until trip meter is reset to 0 ;;;; Release a button within 4 secondsThere will be an audible signal When reset complete.

1. Press and hold the ODO reset button.
2. While still holding the ODO reset, press the IGN button twice without your foot on the brake. The display will show dashes, then zeros to indicate the service reminder is reset.
Other models follow this procedure:
1. Turn the ignition switch to off.
2. While pressing the trip reset button, turn the ignition switch to "IG-ON." Continue to press and hold the reset button until the trip meter displays zeroes

This is the reset proceedure for a 2008 Highlander with a key-type ignition:

Turn the key ON, do not start the engine.

Look at the odometer, and verify that it displays "TRIP A". If it is on "ODO" or "Trip B", press the black stick next to the odometer to read "TRIP A".

Turn the key OFF.

Press in, and HOLD the black trip meter reset button, hold it IN.
DO not release it.

Turn the key ON, do not start the engine

Observe the Odometer display. You will see 5 dashes, then 4, then 3, then 2, then 1 dash, and finally, 5 zeros. Then, whatever number that was displayed on "TRIP A" will be re-displayed..

Now release the black trip meter reset stick.

This completes the reset procedure, and it will be back on in 5,000 miles, to remind you of you next oil change.

Press the info button until you see Trip A or Trip B. Once you are looking at the Trip meter you want to reset, press and HOLD the info button. After 3 seconds, the dashboard will beep and the Trip meter will reset to zero.

This is the reset proceedure for a 2008 Highlander with a key-type ignition:

Turn the key ON, do not start the engine.

Look at the odometer, and verify that it displays "TRIP A". If it is on "ODO" or "Trip B", press the black stick next to the odometer to read "TRIP A".

Turn the key OFF.

Press in, and HOLD the black trip meter reset button, hold it IN.
DO not release it.

Turn the key ON, do not start the engine

Observe the Odometer display. You will see 5 dashes, then 4, then 3, then 2, then 1 dash, and finally, 5 zeros. Then, whatever number that was displayed on "TRIP A" will be re-displayed..

Now release the black trip meter reset stick.

This completes the reset procedure, and it will be back on in 5,000 miles, to remind you of you next oil change.

Hope this helps! Thanks for choosing FixYa!

Reset - step 1 turn the key to the 'on' position. using the trip meter button, toggle the lcd until 'ODO' is displayed. step 2 turn the key off. now, push and hold the trip meter button. while holding the trip meter button, turn the key to 'on'. step 3 while you continue to hold the trip meter button, you will see on the lcd disply five (5) small dashes and they will begin to 'count down' rather quickly. step 4 continue holding the trip meter button and once all the dashes have been cleared, your lcd will display six zeros (000000) - release the trip meter button now - and then the lcd will display 'ODO' and your current mileage. at this time, your 'maintenance required'/oil change light has been reset.