Question about Malber WD1000 Front Load Washer/Dryer

2 Answers

Turn it on...no water?

How the heck do you even turn it on? This is the most annoying waher/dryer ever! Can they possibly make it more convoluted? Help please.

Posted by on

  • Anonymous Oct 26, 2008

    turn it on no water

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If you turn the washer on, but leave the dry time in the "stop" position the dryer will not turn on...I do not dry 75% of my clothes and it works fine for that purpose...

Posted on Feb 04, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Well it turns out that the pipes were not properly connected...however, I think the machine is very confusing anyway. This is my understanding of the Malber WD 1000...at this point in time. I've only used it once. The first dial (on the left) has to do with how fast you want to spin the clothes...I set it at 600 and that seemed to be fine for perm press. The second dial has to do with the temperature...I am still confused...it is the temp of the wash or dry? Its just darn right confusing. The third dial has to do with starting the wash. I put it on 3 for perm press. Now I wonder, if I turn it to 5, delicates, will it still go straight into dry mode? As a woman, I have a lot of things I dont like to dry, so if anyone figures this out before I do, please tell.

Posted on Aug 29, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WASHER KEEPS FILLING .WATER ALL OVER FLOOR.


If the washer keeps filling even after being turned off and pulling the plug then you have a bad water valve.The water valve is the part where the hot and cold hoses hook to the waher.Once in awhile you can remove the valve and clean it out and it will work, if not then you need to replace it.Hope this helped.

Jun 24, 2011 | GE WWRE6260D Top Load Washer

1 Answer

We have a hotpoint WD440 washer dryer which keeps filling up with water even when the power is off. We of course pump the water out but it keeps on refilling.


Your water valve is bad. The water valve is the part where the hot and cold hoses hook to the waher.Sometimes if you take the valve apart and clean it you can get it to work.It is worth trying if this doen't help your problem then you will have to buy a new valve.So it is worth trying.Good luck. I hope this info helped.

Jun 21, 2011 | Washing Machines

1 Answer

Kenmore (Whirlpool) Elite Electric Dryer 110.64086201. Diagnostic check generates a 5E fault code. What the heck is that?


5E - WATER DRAIN ERROR

5E is displayed if the water level frequency detected is 25 KHz or less in the initial phase of the UNB -detecting cycle. The Water Drain error can be cleared by turning POWER SW OFF and back ON.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Sep 28, 2010 | Kenmore Elite HE4 Electric Dryer

1 Answer

How do I install a second hand waher/dryer with limited piping?


1 yes all standard.2 Yes you can get a Y piece. 3 no you will only use water from cold. But you can solve that by going to a good hardware store or B.Q and gettein a self cutting tap for washing machines. You can fit this in just minutes, and do not even need to turn off the water supply. just make sure there is a clean straight piece of pipe to fit it to. 4 yes fit waste pipe to u bend under sink.

Feb 04, 2010 | Washing Machines

1 Answer

Hotpoint Aquarius waher dryer


possible blockage ' filter or could aslo be water coming back from the sink if drain hose too low , you may need to raise this....

Nov 13, 2009 | Hotpoint Ariston Aquarius WD420 Front Load...

1 Answer

No water goig in


Make sure your supply is open. Try rotating the timer clockwise 180 degrees and try again. It could also be a bad water valve solenoid. Make sure power supply is good.

Jul 01, 2009 | Whirlpool WVP9000SB Front Load Stacked...

1 Answer

Need to find the filter as drum not spinning and water leaking


The filter on this model is in the main hose leading from drum to pump. It can be accessed by removing the panel at back of machine.

Dec 13, 2008 | Hotpoint Ultima WD72 Front Load...

1 Answer

Tumble dryer problem


nnot removing steam from drum???? you open your dryer and you see moisture???, if this is a stand alone dedicated dryer ( not a combonatin waher/dryer in one tub), you have a severly clogged/ blocked vent.. you will need to revent or clean the venting as soon as possible

Apr 05, 2008 | Dryers

1 Answer

Indesit widl126s


Suggestion: Possible your outlet filter is blocked; this needs periodic cleaning, depending on your usage. Clean this out and re-fit. Refer to your users' manual re. where the filter is....

Jun 15, 2007 | Indesit WA 125 Front Load Washer

Not finding what you are looking for?

Open Questions:

See all Malber WD1000 Front Load Washer/Dryer Questions

Malber WD1000 Front Load Washer/Dryer Logo

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Malber Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

prem mathew

Level 3 Expert

662 Answers

Cindy Wells

Level 3 Expert

4946 Answers

Are you a Malber Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...