Question about Dayton (4LX41) Heater

1 Answer

Replace worn parts and ware to find them

I have a garage heater and the megnetic switch chatters i have tryed cleaning it but i think it needs to be replaced.the model # 3E033 A, watts 7,500, phase 1, amps 35, moter amps .50, moter volts 240, heater volts 240. i need help if you can give me a location that will sell me the part in my area or any one who will sell me the part it will help thanks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 288 Answers

You didn't give a location, so I cant offer someone to help. I do know that the magnetic switch, otherwise known as a contactor, chatters because its not getting enough voltage at the control coil. It should have a label listing the coil voltage on it, check the power source and go from there.

Posted on Mar 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a mr heater 75 btu garage heater it lites and stays on for 5 seconds and gos out relites gos out than it locks out


Try cleaning the flame sencor , check pilot is clean , check the tubes on the pressure switch are not split and are tight , there are high and low limit switches on there try jumping them out one at a time , see if any of this helps .

Aug 22, 2011 | Mr. Heater Natural Gas Garage Heater -...

2 Answers

I have a gas valve on a lennox furnace that keeps chattering and causes the flame to go off and on constantly. I have replaced the circuit board and flame sensor and cleaned the pilot ignitor. This has...


If the gas valve is chattering it is probably the coil on the valve. You can obtain a ohm reading on the valve and see if you have high resistance with a multimeter. Also check to see if your getting at least 22 volts across the coil should be terminals mv and c on the valve or sometimes there is just a 2 wire plug going to the valve. I think the coil on the vavle is faulty from the info you have given. Feel the black or silver coil on the valve and see if its getting really hot to touch. I would replace the valve

Dec 23, 2010 | Dayton Gas Lonox Furnace Heater

1 Answer

I have a natural gas heat star garage heater it will stat but it wont light


try jumping out the pressure switch see if it lights , or first unplug heater and replug in might reset or it could need a clean

Dec 11, 2010 | Mr. Heater HeatStar Radiant Tube Heater -...

1 Answer

Where can I purchase parts for my All-Pro


there is no clutch on this unit.it is an air pump that has rotor and vains.All pro heater parts are getting few and far between. try this place they have some of the parts but not all.if your ignitor ever goes out there are non to be found.they are no longer avalible.......www.portableparts.com

Feb 19, 2009 | All-Pro Kerosene Garage Shop Heaters - All...

Not finding what you are looking for?
Dayton (4LX41) Heater Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dayton Heaters Experts

paulcarew

Level 3 Expert

1862 Answers

Lawrence Oravetz

Level 3 Expert

7565 Answers

Brad Brown

Level 3 Expert

13529 Answers

Are you a Dayton Heater Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...