Craig CMA3568 speaker no sound

Hey, for the pairing of the Craig CHT729 speaker use these steps:

1: Turn on the speaker.
2: Press and hold the (power) PAIRING button until you hear the voice guidance and the (Bluetooth) indicator begins to flash quickly.
3: Perform the pairing procedure on the Bluetooth source device to detect the speaker.

Or for more instructions search at this link:

Manuals.plus

Hi
Try this.
Hold Down Power: Many Bluetooth speakers switch into pairing mode by turning the speaker off, then turning the device on while keeping your finger depressed on the power button. To notify you the speaker is in pairing mode, it will typically emit a sound or its light indicator will begin flashing rapidly.
Hold Down Pairing Button: Some Bluetooth speakers have a dedicated button for placing your device into pairing mode. Seek out a button on your device with the Bluetooth symbol next to it, then hold it until you hear your speaker emit a sound or its light indicator begins flashing rapidly.
your Bluetooth speaker now discoverable, it can be paired to your iPhone or Android phone.
Quick Pairing Instructions

1. Open Settings.
2. Open Wireless and Network.
3. Open Bluetooth® Settings.
4. Turn Bluetooth® on if it is off.
5. Touch Search for Devices.
6. Touch and hold - UGO.
7. Touch Connect.

You will need to place the sound bar's Bluetooth feature is "discovery" or "pairing" mode and then follow the tablet's usual method of connecting it to a new Bluetooth device. Once paired you can redirect the tablet's audio to the sound bar. You may also be able to use a 3.5mm to RCA plug cable (usually used to connect PC sound cards to amplifiers or powered speakers) to connect the tablet's headphone jack to the sound bar's A/V audio inputs.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/dave_fb2c45146b845cea

You can try one of two ways:

1. If your speaker has a headphone jack, you can connect your cellphone to the speaker headphone jack-to-headphone jack using an audio cable with headphone plugs at both ends.

2. If your speaker/subwoofer combination is Bluetooth-enabled, pair your cellphone with the Bluetooth speaker.

Hope this helps.

1. Press and hold the button to put the speaker in "Pairing/Connecting" mode. You should see a red and blue light flashing in rapid succession somewhere on the speaker.
2. Turn on Bluetooth on the phone and tap on Scan. The phone will start scanning for nearby Bluetooth devices. When you see that it detected a device with a name similar to the speaker's name, tap on the name to pair with the phone. If you are asked for a passcode/passkey, enter '0000' or '1234' (without the quotes). If the two pair, the light on the speaker will turn to a steady blue and you will see 'Connect' on the phone. Tap on Connect and then you will see Connected on the phone. Your phone and the speaker are now connected.

The steps above should be detailed in the set up guide that came with the speaker. There may even be a passkey/code provided in the guide. Use that one for pairing instead of the passkey I suggested above. Please note that pairing is a one-time procedure, required only the first time you are connecting the phone to the speaker, a "get to know you" procedure. After that, you just need to connect the two.

turn both phone bluetooth and speaker bluetooth off. then turn them back on. the speaker's light should be flashing indicating its searching for a device to pair with. as its flashing make sure your phones bluetooth is visible and searching. they will pair and your phone will tell you and the speakers light should quit flashiing and just remain on.

Turn on the bluetooth of your phone first: Go to settings>Wireless and Networks>Enable Bluetooth and disable discovery limit in bluetooth settings. After that make sure the bluetooth in your speaker is on and let your phone search the speaker and let it pair with it after that go into your phone's music player and look for its play options and if you see via bluetooth click it. Just let me know if you need further instructions or you could watch this video showing how he pairs his bluetooth speaker from his phone DBEST London Bluetooth Mini Speaker Review

To Pair:
1. Turn on your Bluetooth speaker (slide switch to BT)
2. Light on bottom should turn on Blue. If not, plug speaker into USB connector and bottom will turn Red to indicate it's charging.
3. Make sure Bluetooth is turned on your PC or Phone. Select device name: CMA3532BT.
4. Enter pairing code (passcode): 0000 or you can try: 1234

To Pair:
1. Turn on your Bluetooth speaker/headphones (slide switch to BT)
2. Light should turn on Blue. If not, plug speaker into USB connector and light will turn Red to indicate it's charging.
3. Make sure Bluetooth is turned on your PC or Phone. Select device name: CMA3532BT.
4. Enter pairing code (passcode): 0000 or you can try: 1234

Through basic hacking, the code 0000 worked for me....
I wish it came to me sooner!

Craig Electronics CMA3532BT is the model number -
A tiny cylinder speaker - sounds pretty good for the tiny $$$ too.
MikeFilosa