Question about DCS BGA27-BQ (NG) Grill

1 Answer

Burner will not light

I am having a problem with my DCS 36" grill. The burner will not ignite. I have checked the ignitors and all of them are sparking. The gas seems to be coming out and I can light them with a match or lighter. Every once in a while I can get one of them to light when the gas is moved to the med or low position. What is wrong?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Possibly the ignitor has a weak spark its making the jump to the burner but not strong enough to lite the gas did you check the lines for spider webs or other insects?

Posted on Jun 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why wont the left and right burners lite using the electric ignitor?


Are the igniters for those burners sparking?

Aug 29, 2014 | Grilling

1 Answer

DCS 36 in. CS-366 LP Cooktop ignition


in that burner something is short check it out

Dec 09, 2007 | DCS 36 in. CP-366 Gas Cooktop

1 Answer

10 year old DCS Oven does ignite. Oven ignitor glows but maybe not enough to trigger LP from being introduced?


just because the ignitor glows it doesn't mean it's good,it takes 3.2 amps for the ignitor to open the gas valve and ignite the flame,usually if the flame doesn't ignite in around 40 seconds the ignitor is bad.also check the burner tube,your model number doesn't come up so i don't know if you have one or two ignitors in this oven but i've found that when the ignitor starts to fail and the customer waits to long to have it looked at the ignitor burns a hole in the tube and then both the ignitor and tube has to be changed,hope this helps and good luck with your oven.

Jul 19, 2013 | DCS RGU-486GD-L Range 48", 6 Burner,...

1 Answer

Ignitor doesn't work on DCS grill


Just use a 9 volt batterie

Jan 20, 2018 | DCS Grilling

1 Answer

Ignition


The problem most likely the ignitor itself. If you have the paperwork that came with the grill, It should have an origional replacement parts page. If not, you may be able to get a universal at your local hardware or home supply store.

Jun 11, 2012 | DCS Grilling

1 Answer

We just put together our Genesis E320 LP Grill. The ignitor is not igniting the far right side of the grill. It does ignite the first two knobs and the side burner. What is going on?


I have a new EP320 and my instructions specify that the ignitor lights Burner #1 and the other grill burners light off of that - Burner #2 second - Burner #3 lights last off of Burner #2.
Gary

Jul 04, 2011 | Garden

1 Answer

Igniter doesn't work. New battery installed.


First, make sure the battery if turned in the proper direction. On most grills, the + end should face you. Also, check for any corrosion inside the batter holder, If you see any, clean it out with a Q tip and a little WD40. Check the wiring behind the control panel where the ignitor module is located. Be sure all the wires are still attached and the ground wire is attached firmly. If none of this solves the problem ... Remove the cooking grates and flame tamer and clean all of the ignitors next to the burners. They may be covered with grease. A cotton ball and alcohol works well to clean them.

If by some slim chance, none of the above solves the problem, it's time to replace the ingnitor assembly. You can purchase it directly from DCS or the dealer you purchased the grill from.

Hope this helped to solve your problem.

Mar 07, 2011 | DCS BGA27-BQ (NG) Grill

1 Answer

DCS Cooktop CTD-365 one burner won't ignite/no spark or ticking. I cleaned ignitor.


Hi,
Here is a tip that I wrote to help people troubleshoot problems with their cooktops not igniting.

Cooktop Range Stove spark ignition does not work
http://www.fixya.com/support/r5649407-cooktop_range_stove_spark_ignition_not

heatman101

Aug 11, 2010 | DCS 36 in. CTD365N / CTD365L Gas Cooktop

2 Answers

Infrared burner goes out


if there is a thermocouple on the burner this could be out of postion or brunt out

May 17, 2010 | DCS BGB36BQARN (NG) Stainless All-in-One...

Not finding what you are looking for?
DCS BGA27-BQ (NG) Grill Logo

Related Topics:

377 people viewed this question

Ask a Question

Usually answered in minutes!

Top DCS Grilling Experts

Paul Carew

Level 3 Expert

3328 Answers

Gary Kenady
Gary Kenady

Level 2 Expert

140 Answers

joel920368

Level 2 Expert

89 Answers

Are you a DCS Grilling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...