Maytag fridge MFI2266AES control panel flashes PE0000

there's a website reliable-store
all heavy eq uipment repair issues servicing, loading, wiring, engine problems everything is covered here its a must try

You need the high voltage control board. WPW10310240 Start making plans to unplug the refrigerator and save the food.

You need to program the new board. Programming Mode:

NOTE: The Program Code is located on the Serial Plate on this unit after the word Code.

1. Press and hold the Door Alarm Keypad .

2. Press and hold Freezer Temperature Down Keypad .

3. Release the Door Alarm Keypad and wait 3 seconds.

4. The control will display PE to indicate the programming mode.

5. Entry is confirmed by pressing the Freezer Temperature Down Keypad once more.

6. The control will display the current Program CODE. This value should be validated with the



Program CODE printed on the unit serial plate.

NOTE: If the Program CODE is correct, the Programming Mode is exited by pressing Door Alarm Keypad for 3 seconds.

7. Press the Refrigerator Temperature Up Keypad or Refrigerator Down Keypad to change the digit value with each key press.

8. The decimal point indicates the selected digit. Press the Freezer Temperature Up Keypad to select the next digit.

9. Once the desired Program CODE is entered, press and hold the Freezer Temperature Down Keypad until the Program CODE begins flashing indicating it has been saved.

NOTE: If you attempt to enter an invalid Program CODE the control will not save the new code, but will beep. (The unit will NOT run with a Program CODE of 0000).Once the Program CODE has been saved the Programming Mode is exited by pressing any key. If the new code is incorrect this process should be repeated.

The Programming mode can be exited at any time

If you replaced the front control board your issue may be your water tank. How long after you filled your bottle did it stop working?

possible bad dispenser board

We are having the same problem...we have been without a refrigerator for over a month now. We cant get anyone to answer service calls. Did you get yours fixed? If so how did you? Our refrigerator isnt even a year old. Any information would be greatly appreciated. Thanks

Follow the instructions that I found.

Did you check the low voltage supply going to the board? I'm pretty good with that model Only problem is I can't pull that model number up. Looks like you have an extra number or letter. You should get 16 volts from the low voltage side of transformer. Sea Breeze

Go to this web page to find the text answer below: http://www.fixya.com/support/t233614-reprogram_hv_board

HERE TIS RIGHT OFF THE INSTRUCTION SHEET.  THE TECH JUST LEFT. POWER UP REF. PROGRAM CODE IS LOCATED ON SERIAL PLATE ON THIS UNIT AFTER THE WORD CODE.-1. PRESS & HOLD THE DOOR ALARM KEYPAD.-2. PRESS & HOLD FREEZER TEMP DOWN KEYPAD.-3. RELEASE DOOR ALARM KEYPAD AND WAIT 3 :WILL DISPLAY PE TO INDICATE PROGRAMMING MODE-5. ENTRY IS CONFIRMED BY PRESSING TEMP DOWN - KEYPAD ONCE MORE.-CONTROL WILL DISPLAY CURRENT PROGRAM CODE. THIS VALUE SHOULD BE VALIDATED THE THE PROGRAM CODE PRINTED ON UNIT SERIAL PLATE.-NOTE: IF PROGRAM CODE IS CORRECT, THE PROGRAMMING MODE IS EXITED BY CLOSING THE FRIG DOOR.-7.PRESS REFRIG TEMP UP KEYPAD + OR REFRIG DOWN KEYPAD -TO CHANGE THE DIGIT VALUE WITH EACH KEY PRESS.-8.THE DECIMAL POINT INDICATES THE SELECTED DIGIT. PRESS THE FREEZER TEMP UP KEYPAD + TO SELECT NEXT DIGIT.-9.ONCE DEIRED PROGRAM CODE IS DISPLAYED, PRESS AND HOLD THE FREZZER TEMP DOWN KEYPAD - UNTIL UNIT PROGRAM CODE BEGINS FLASHING INDICATING IT HAS BEEN SAVED. *note* IF YOU ATTEMPT TO ENTER AN INVALID PROGRAM CODE, THE CONTROL WILL NOT SAVE THE NEW CODE, BUT WILL BEEP! (THE UNIT WILL NOT RUN RUN WITH A UNIT PROGRAM CODE OF 0000). ONCE THE PROGRAM CODE HAS BEEN SAVED THE PROGRAMMING MODE IS EXITED BY CLOSING THE FRIG DOORS.  

This sounds like the Maytag bottom mount that has a High Voltage Control Board problem. Does this have the freezer/fridge temp. display/controls on the left hand fridge door? Whats the model number and on the manufacture tag does it something on it like Code:0304 maybe? Let me know I may have an answer I do work on these for a living.