Question about Computers & Internet

1 Answer

NAS Drive by ADS Tech not recognized on network.

ADS Tech NAS kit, Maxtor 250GB HD inside, attached to D link router,  power is on, router led acknowledges connection, but no icon on either my Dell GX1 with XP sp2, or my eMac with OS X 4.11.
Any help will be greatly appreciated. Thank you. Tim

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

You can log into your router and find out what IP address has been assigned to your NAS unit.

Then start up Internet Explorer Or Firefox and go to the address http://xxx.xxx.xxx.xxx (replace with the IP address of the NAS unit).

That should get you in. Then you will have to set the workgroup and share parameters. Once you have it setup you can always map the NAS unit and use it as a external hard drive.


Posted on Jan 05, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Technician can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Technician (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Cannot get external hard drive to work


- Make sure that the hard drive (HD) is properly connected to the computer.

- Try connecting it to a different computer to make sure that the HD is the problem.

- Check the Disk Management in your computer to see if the HD could still be detected. Once detected, reformat the HD and it should work again.

To check the Disk Management:

NOTE: Make sure that the external HD is connected and turned ON.

1. Right-click "My Computer" (XP) or "Computer" icon (Vista)
2. Select Manage and click on "Disk Management".
3. From the Disk Management, you will see a drive letters
4. Write down all the drive letters and then disconnect the Maxtor HD from the computer.
5. If there's a drive letter that disappears, then that is your Maxtor HD.
6. Reconnect the Maxtor HD and reformat it. You may right-click the drive letter and there's an option to format the HD.

If you're hearing a clicking sound while the HD is turned on, mostly, it's already defective.

Have a great day!

Oct 17, 2009 | Maxtor Hard Drive

1 Answer

Maxtor one touch 4 mini 250GB hard drive beeping


I had the same problem and the Maxtor/Seagate website did not have any solutions. I finally got in touch with Tech Support and got a fix. I was using it with a Dell tower and plugging into a USB port in the front. I also was using an after market cable.

I learned the Maxtor is a power hog and beeps and shuts down when it is not getting enough power. I did not know but the USB ports on the front of a desktop/tower computer do not provide as much power as a port on the back (the back ports are sometimes directly connected to the motherboard). I got a USB extension cable and connected it to a USB port in the back and it solved the problem.

I also learned that most laptop USB ports are not powerful enough to run the Maxtor. Mine would also not work if you attempt to share it by using an unpowered USB hub. I have gotten it to work with a powered desktop USB hub (Belkin).

I believe that this may explain why you get a "Y" cable with the drive. I could not find an explaination for the cable or how to use. There may be an accessory to purchase that attached to the cable and powers it.

Oct 15, 2009 | Maxtor OneTouch 4 Mini 160GB External USB...

1 Answer

Belkin N+ modem router (F5D8635) not recognizing Maxtor 1TB HD


I could not find the F5D8635 model but here is the Firmware update page for the N1 Vision Router.
Try updating your firmware.

Jul 03, 2009 | Belkin N1 Vision Wireless Router

1 Answer

SECOND HARD DRIVE NOT RECOGNIZED


Change the settings of you IDE drives in your BIOS. Set your secondary boot device to HDD1. Also make sure that your primary HDD is set to master and the secondary HDD is slave. The jumper is found at the back of the hard drive where you connect the power and IDE cables. Try this and post back as to how it went..

Nov 11, 2008 | Seagate 250GB Barracuda 7200.10 ATA-100...

1 Answer

LAN led light alway on and flashing


Reset the router:
While the router is powered on press and hold the reset button for 5-10 sec. Release the button and wait until the router boots up (1 min).

If this does not work then you can try this

Try setting it into recovery mode and loading firmware:

Unplug power cable from the router and press the reset button. While holding the reset button plug the power cable in. Continue holding the reset button untill you will see LEDs on the router flashing rapidly.

You should be able to log into the router - you will see a prompt to load firmware. The firmware is available on our WEB site: http://www.dlink.com.au/tech/

Note - suggest you d/l the firmware BEFORE you reset router

Jul 05, 2008 | D-Link DI-704P Router

2 Answers

My old Dell HD will not fit in HP w/vista


i see..well..was the old hard drive running xp by chance?..seems that with the new vista, that each application would need to be upgraded with drivers to pull the old data..another option is to use a data recovery service.

May 10, 2008 | NexxTech Portable Hi-Speed USB 2.0 Kit...

3 Answers

Maxtor OneTouch 4 Mini 250GB External Drive Does not show up on my computer


Are you connecting Drive via a USB hub or direct into two separate USB sockets on PC?

May 05, 2008 | Maxtor OneTouch 4 Mini 160GB External USB...

1 Answer

Dlink Router not assigning IP to NAS


DI-624 (Update to FW 2.70+)

See: http://www.infrant.com/wiki/index.php/Hardware_Compatibility_List_-_Network_Switches/Routers#D-Link

Dec 28, 2007 | D-Link DI-624 Air Plus XtremeG Wireless...

1 Answer

Driver for Maxtor 71336A


Vista ULTIMATE has all driver incudes!So you dont need extra driver for ur MaXTOR!Just make sure ur OS runin OK and run UPDATE

Dec 28, 2007 | Maxtor Hard Drive

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

203 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

kakima

Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14162 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...