Question about E-Machines eMachines Desktop PC

1 Answer

I have an emachines t6520 and the power sw wire, HDD led wire, and the power led wire hve been disconected

Where do they go?

Posted by on

  • 1 more comment 
  • flipscamels Oct 29, 2008

    the power sw wire, hdd led, and power led have came unpluged where do they go?

  • flipscamels Oct 31, 2008

    asked question again



  • dbaerwald Jan 09, 2009

    I have the same issue on emachinet6520 mother board- but there are no markings like LED or Pwr on my board- 9 sets of pins, two have only one pin on set. Colors are different then cords- cords all have one white, plus either red, blue or black. Pins have green, red, black, blue, yellow(nothing) but no white. Please help.

    dbaerwald@gmail.com

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • E-Machines Master
  • 4,338 Answers

On the system board, on the left edge next to the primary IDE connector, there is a 9 pin header.
I usually get a magnify glass and look down on the header . From right to left,you will see PWR led pins closer to the edge of the motherboard.and the Power BTN next to it.(the side of the pins that has 4 pins on it)
Then on the other side, you will see the pins for the HDLED across from the PWR led. Then the Reset pins across the PWR BTN.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe

Posted on Nov 02, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the wiring diagram that shows where on the motherboard to plug the power switch ,power LED, and HDD Led on a T6520 emachine desktop


Most Motherboards are made to only accept certain plugs in that specific spot! If you are trying to add something new like a new Fan or LED, or HHD and you need power you would have to use a 4 prong plug off the power supply, If your power supply does not have any more available plugs, Amazon.com or Newegg.com sells splitters!

Good Luck and Best Wishes!

May 03, 2011 | Computers & Internet

2 Answers

I cleaned my pc, and disconected the wires that are right downside corner. I cant remember how to put them back rightly. Any help? hdd led power led + power led - power switch (sw) reset switch (sw)


H57H-AM2 v2 Motherboard in a Gateway DX4840 wire connections for Front Panel are shown here in Photo. I took them before I disconnected mine so it works.3_3_2012_12_10_44_pm.jpg3_3_2012_12_10_56_pm.jpg

Jun 15, 2010 | EliteGroup ECS L4VXA2 (CDL4VXA2)...

1 Answer

Need to re-attach power button cable, hard drive


The manual for your computer is available from emachines, p.168 shows the info you need (replacing the front I/O panel)
http://downloads.emachines.com/userguides/8511279_eM_NG3_chassis_HW_ref_en.pdf

The good news is that you can't harm the computer by connecting the wires wrong and the bad news is they just won't work the way they are supposed too if not connected properly. The LED's must have the correct polarity to work.
In general, if you look real close (as in magnifying glass and flash light) you will see the ID for each set of pins is printed on the motherboard (pwr,rst,HDD,pwr sw,speaker) Just match what it says on the motherboard to what it says on the wires. Don't worry if you get the polarity wrong. If a light doesn't work just swap the two wires. The colored wires should be positve (+), though. The reset (rst) and power switch (pwr sw) wires don't require polarity.
These instructions are for most computers in general, YMMV.

Nov 30, 2009 | E-Machines eMachines Desktop PC

1 Answer

Power Button wire to mother board power led power sw HDD Led . what pin connects to the three wires from power button. Led Power wire to what pins, HDD Led to what pins and power SW to what pins on the...


There are may motherboards, but most have writing on them as to what is suppose to plug where. For example, for the power switch, the lettering might be "Pwr" or "Power" or "Pwr sw". The pins are usually together and should fit the plug on the end of the wire.

Nov 25, 2009 | E-Machines eMachines Desktop PC

1 Answer

I unplugged my power sw wire, hdd led, and power led of my emachines t6520 ive tried everything but the computer will not turn on the motherboard does not have any symbols to indicate pos or neg . . . . |...


open up you pc case...mind out for static! dont touch what you dont have to and look for a printed ( normaly white ) motherboard model id..this might be the name of a manufacurer or just a few letters and numbers plus a revision number at the end. armed with these, trot of to google and stab them in. you should see a host of sites, but look for one that is the support site for your board...track down you board on the support/download site and there should be a manual & drivers ect to help you :)

Oct 07, 2009 | E-Machines eMachines Desktop PC

1 Answer

T6410 EMACHINE TRYING TO CONNECT START BUTTON


The motherboard in your computer is an MSI MS-7145, which is also called RS480M. You can download a copy of the manual here. The front panel connections are on page 2-20.

Looking at the header JFP1, pins 1 through 9 (odd numbers) are the front row, pins 2 through 10 are the back. Pin 10 is the missing pin. The power switch connects to pins 6 and 8. The power LED connects to pins 2 and 4. The HDD LED connects to pins 1 and 3. The reset button, if used, connects to pins 5 and 7.

May 13, 2009 | E-Machines eMachines Desktop PC

2 Answers

NEED POWER SWITCH WIRING FOR A EMACHINE T-3095


check on the motherboard there should be a small prints on it near control panel.

Mar 05, 2009 | E-Machines eMachines T3830 PC Desktop

1 Answer

Hdd led off


see to the front panel section on mother board possibly on the right hand side of bottom u can see the label there to connect hdd led

Dec 28, 2008 | MSI RS480M-IL (816909008517) Motherboard

1 Answer

Wires unpluged


these normally go at the front of the motherboard if you are looking at it where the power supply box cables are at the back. There are litlte pins that these fit onto that will say on the motherboard Hdd led etc... in small writing.

hope this helps

Oct 31, 2008 | E-Machines eMachines Desktop PC

Not finding what you are looking for?
E-Machines eMachines Desktop PC Logo

Related Topics:

556 people viewed this question

Ask a Question

Usually answered in minutes!

Top E-Machines Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18377 Answers

Are you an E-Machines Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...