Jimmy gmc 1997 stop lights are not working, but turn signals are working, stop light fuse is ok, hazard and turn signals flasher working good. I would like to know why stop lights are not working.

brake lights not working - 1997 GMC Jimmy - RepairPal

repairpal.com > Questions > GMC > Jimmy > 1997 GMC Jimmy

Jan 11, 2011 - hi about 2 days ago i realized my brake lights were not working but my turn signal lights were working and parking lights as well but no brake ...

Tail Lights don't work but third brake light does, not fuses ...

answers.edmunds.com > Edmunds Answers

Sep 23, 2009 - 97 GMC Jimmy 4x4 blinkers work, reverse lights work, above window ... I just lost hazard lights and rear brake lights, they were working 2 days ... If it is a frayed wire or solder point, then you can repair it, but not any worn contacts. ... Does anyone have any suggestions on 1997 Honda Accord tail & brake lig.

did both signal lights stop working at the same time or not,it may just be the signal flasher has gone bad,it is located under the dash by the fuse panel.if the hazard flashers work then i would say the signal flasher is bad.with the hazards on you can locate it and that is what the signal flasher looks like and it is a separate flasher,

Replace the flasher, this truck uses two flasher one for the hazards and one for the signals, check and replace the flasher and go from there, good luck.

the fuse might be good, but the flasher canister is bad, located near fuse panel

Sounds like the flasher unit has gone bad. It is mounted behind the glove compartment. I would also check the fuses in the fusebox under the hood.

There are a row of Allen head and 9/16 nut screws on the bottom panel below the steering wheel and middle panel, remove those.
Gently pull down lower panel, upper panel will pull out as well slightly. The hazard flasher (left) and turn signal (right) are just to the left of the lighter assembly. (Silver)Relays are difficult to pull out, if you gently use wide mouth pliers , rock them out. Replace and test, before reinstalling panel.
Thank you for using fixya and be safe

First you need to replace the turn signal flasher its mounted in behind the kick panel cover on the drivers side.the cover is difficult to remove,once you have it out of the way they will be two flashers.One is the for the hazards and the other is for your turn signals,make sure you check the flasher before you reinstall the cover.

Check turn signal fuse, if fuse is good, check turn signal flasher, this is identical to hazard flasher, I believe on the 1997 it is located under the dash near the center console. The turn signal and hazard flashers are the same part number so try switching places with them and see if the turn signals work. If turn signals work after switching them you need a flasher.

the flasher is right below the radio,under the dash .it take 3or4 screws to take off panel.both flashers are under there.one for your 4 ways,and one for your turn signal.if your four ways work you can fill the flasher to determin which is witch. mine the four ways was on the left,turn signal on the right.they are not in the back of glove box.ther is apanel there with three relays but not for your turn signal.thank u gm jim.u helped me find them.

The wire under the hazard button has probably come loose. Most GMC vehicles this year range were made with a closed circuit wiring between the flashers, hazard lights, and rear defrost. Over time the wiring under the hazard button has been known to loosen. This causes the whole system to lose function. If pop out the hazard button on you center console you should be able to tighten that wire back on and the system should work again.
The same thing happened to me when I put in a new radio. I bumped the wires off and my blinkers, rear defrost, and hazard lights went out. I replaced the fuses and the flasher relay but nothing. Then I asked a mechanic and he told me what I just told you.
Hope it helps!