How to remove r1 2010 tank - YZF-R1 Yamaha Motorcycles

RTM ,. read the shop manual first.? its all there to read 24/7.
Is this car A USA CAR?

generic.

1. drain tank fully, or you will get a flood of fuel on YOU.
2. remove all hoses to tank/vents and wires, to pump rack top,.
3. remove filler neck hose to tank.
4. with a floor jack under tank, and wood protector to it, try to raise tank just a tad. (1/2?") (I have car at rear on jack stands first)
5. remove tank straps. now.
6. lower jack, done.

now out of shop manual quoted SX4 , near.

1) Relieve fuel pressure in fuel feed line according to
"Fuel Pressure Relief Procedure".
2) Disconnect negative cable at battery.
3) Remove fuel filler cap.
4) Insert hose of a hand operated pump into fuel filler
hose (1) and drain fuel in space "A" as shown in
figure.(this car has check valve at tank inlet)
Hoist vehicle, and remove clamp (2), fuel filler hose
(1) and breather hose (3) from fuel filler neck.
6) Remove exhaust center pipe referring to "Exhaust
Pipe and Muffler Removal and Installation in Section
1K".
7) Remove propeller shaft (For 4WD model) referring to
"Propeller Shaft Assembly Removal and Installation
in Section 3D".
8) Due to absence of fuel tank drain plug, drain fuel
tank by pumping fuel out through fuel tank filler.
Use hand operated pump device to drain fuel tank.
Disconnect quick joint (fuel pipe) (1) from fuel pipes
(2) referring to "Fuel Hose Disconnecting and
Reconnecting".
10) Support fuel tank (1) with jack (2) and remove its
mounting bolts (3)
Lower fuel tank a little as to disconnect wire harness
at connector (1)and ground wire (2), then remove
fuel tank

Removal and Installation

1. NOTE: Make sure fuel tank (9002) is properly supported during removal and installation procedures.
   Drain fuel from fuel tank .

1. Loosen fuel tank filler pipe clamp.

1. Remove fuel tank heat shield (9A032) from vehicle.

1. Support fuel tank .

1. Remove bolt from rear fuel tank support strap (9092) and remove rear fuel tank support strap .

1. Remove bolt from front fuel tank support strap and remove front fuel tank support strap .

1. Partially lower fuel tank to gain access and remove feed and return lines from sender ports. To disconnect push connect fittings, refer to Push Connect Fittings in this section.

1. Remove electrical connector from sender unit.

1. Remove fuel vapor hose from evaporative emission valve (9B593) .

1. Lower fuel tank from vehicle.

Procedure to remove a fuel tank depends on brand, model and year of the car. Just some examples:
How to properly remove gas tank

How To Remove Gas Tank

How To Remove The Fuel Tank

How to drain your car fuel gas tank

Drain the gast tank. Remove the chrome bolt holding the dash to the tank. Lift up the dash and disconnect all the electrical connections. Remove the dash. Remove the seat. Remove the bolt at the bottom tank mount. Remove the nut and bolt at the bottom front of the tank. Disconnect the gas line on the left side bottom of tank. If the tank has a crossover line at the front, disconnect it. Lift the rear of the tank and block it up with piece of wood or something similar. Disconnect the electrical connection for the gas gauge under the left side of the tank. Remove the tank. Installation is reverse of removal. Don't forget to reconnect the fuel gauge and gas line, and crossover, if equipped. Good luck!

You need to remove the gas tank to access the plugs.

*Remove the rear seat
*Remove the front seat
*Remove the single bolt holding the tank on
*Remove the 3 screws holding the speedometer on, left the speedo and unplug the wiring harness
*Disconnect the fuel line on the left side of the tank
*Lift the tank and unplud the wiring harness from under the tank (California models have an extra hose to disconnect
*Carefully lift the tank up and back to remove the tank from the bike.

Gas tank is located inside of fuel tank. Loosen the two straps on tank and let the tank drop slowely with floor and wood support underneath.(make sure gas is removed so it is not so heavy) Lower tank and remove electrical wire connections and remove filler hose from tank side.Remove tank from car. Tank has round o ring lock on top.Take rubber malet and tap o ring counter clockwise to remove pump assembly replace pump and then use reverse procedre to put tank back.Good luck.

I believe this is same truck as Ranger

Pump is in tank

Removal
NOTE: On some vehicles, fuel gauge sending unit is not available separately. On those vehicles, to replace sending unit, replace entire fuel pump .

1. Remove fuel tank as described in this section.

Removal and Installation
NOTE: Make sure fuel tank is properly supported during removal and installation procedures.

1. Drain fuel from fuel tank .

1. Loosen fill pipe clamp.

1. Remove bolts securing shield and bracket assembly to frame (5005) and remove assembly from vehicle.

1. Remove fuel tank filler pipe from vehicle.

1. Support fuel tank .

1. Remove bolts and nuts from rear fuel tank support strap and remove rear fuel tank support strap .

1. Remove bolt and nut from front fuel tank support strap and remove front fuel tank support strap .

1. Lower fuel tank .

1. Remove fuel feed hose at sender push connector.

1. Remove fuel return hose at sender unit push connector.

1. Disconnect sender and fuel pump electrical connector.

1. Remove fuel vapor hose from fuel vapor valve .

1. Lower fuel tank from vehicle

1. Remove fuel tank to bench. Remove any dirt that has accumulated around the fuel pump attaching flange so that it will not enter the fuel tank during fuel pump removal.

1. Turn the fuel tank sending unit locking retainer ring (9A307) counterclockwise with the Fuel Tank Lock Ring Wrench Tool T90T-9275-A or T86T-9275-A and remove fuel tank sending unit locking retainer ring .

1. Remove the fuel pump and sender assembly.

1. Remove fuel pump mounting gasket (9417) and discard.

1. If necessary, disconnect spade connector and remove two screws and fuel gauge sending unit.

check fuel filter first. rate as fixed if this helps.

Steel Midship, Aerostar
Removal and Installation

1. NOTE: Make sure fuel tank (9002) is properly supported during removal and installation procedures.
   Drain fuel from fuel tank .

1. Loosen fuel tank filler pipe clamp.

1. Remove fuel tank heat shield (9A032) from vehicle.

1. Support fuel tank .

1. Remove bolt from rear fuel tank support strap (9092) and remove rear fuel tank support strap .

1. Remove bolt from front fuel tank support strap and remove front fuel tank support strap .

1. Partially lower fuel tank to gain access and remove feed and return lines from sender ports. To disconnect push connect fittings, refer to Push Connect Fittings in this section.

1. Remove electrical connector from sender unit.

1. Remove fuel vapor hose from evaporative emission valve (9B593) .

1. Lower fuel tank from vehicle.

remove seat, remove console on top of tank, disconnect wiring from console to tank, disconnect vent line if present, disconnect fuel line on tank, disconnect fuel gauge (up under tank on left side, 3 wires, 4 wire connector, wires are yellow, orange, and black), remove bolt at rear of tank, remove two side bolts up front under tank (coil bracket is there also, carefully cut clamp on cross over hose located up front under tank.
This works better with three hands remove one side of cross over hose, fuel will flow freely so the extra hands are good at "plugging" the hose and the tank. Gently remove tank tilting front of tank as much as you can till you get it clear of the frame, while still tilted at a steep angle put the cross over hose back on.
To make things easier drain all fuel out of tank before reversing the process to reinstall tank. Hope this helps.

JP

• You have to remove the fuel tank.
• Remove front seat. Use your key.
• Remove rubber caps from the fuel shut off valves. Run screws in all the way to shut fuel off.
• Remove speedo dash – 3 qty # 5mm Allen. Unplug all connectors including the small white one. Note order of plugs then un-snap from brackets on tank. Disconnect vent line.
• To remove fuel tank. Remove decorative fins at the front of tank. 2 allens #4 on each side.
• Remove two 10mm nuts at rear bracket holding tank.
• Remove 2 qty 12mm bolts at the front bracket holding tank.
• You can also swing the tank around and set it on the frame, or on a chair, without disconnecting the fuel lines. Remember to protect the frame and tank with a towel.
• The air box is under the tank. Remove the top cover and replace the filter.
• You can improve performance by removing some air restiction, Using a 1" hole saw drill 6 holes in air box cover to let it breath better.

NOTE: At least 1 person has reported that the soft fuel lines can start leaking after using this method multiple times. If you smell gas, it may be time to replace the stock fuel lines with a higher grade automotive gas line (7/16").