Question about 1994 Honda CBR 600 F(2)R

1 Answer

Breather pipe the two breather pipes that are fixed 2 the tank .the smaller pipe where does the oher end fix to

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that gotĀ 5 achievements.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.

  • Contributor
  • 29 Answers

The smaller pipe is the 'breather' pipe and should follow the other pipes below the tank and just sit there

Posted on Dec 15, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

There is a open ended pipe that runs above engine oil intake, the other end has a hose connected to it? mines leaking fluid thinking gas

Catch what is dripping and see if it smalls of gas, oil or water. Whatever it is I doubt it should not be open ended and should have a hose attached to it that goes somewhere.

Sounds a bit like an Oil Breather Pipe at that diameter.

Take a look at these.

Oil Breather Pipe Bing images

Jan 05, 2016 | 1997 Dodge Grand Caravan

1 Answer

How do you route vent line form tank? Where does other end go?

what machine? most breather pipes go up and into the starter cowling. machines like newer stihl have breathers that just sit on top of the tank

Mar 05, 2015 | Garden

1 Answer

Fitting evo oil tankwith different pipes

There are 3 connections on the new tank. 1- feed/suction. 2- return. 3-breather. You should be able to look inside the tank and tell which is which. The 2 coming in the front botton is feed and return. The return should have a small tube sticking up inside the tank. The feed will not have a tube on it. The breather will be at the top of tank (if it is on the bottom it will also have a tube sticking up inside the tank.

Nov 30, 2013 | Motorcycles

1 Answer

I have a Husqvarna 385 XP and rebuilding it. Ran into a problem hooking the fuel lines back up. I am trying to figure out where the line from fuel tank with filter connects. Also there is the other line...

The port on top of the carb ( pump cover ) takes the pipe from the crankcase, this is the pulse to work the pump diaphram, the pipe with the filter on the end goes to the port lower down on the carb, the other pipe from the tank is the tank breather, it just pushes onto a plastic nipple on the orange plate under the carb, this pipe is only to keep dirt out of the breather but needs to be open .so the nipple is just somewhere to keep the pipe held.

Oct 16, 2011 | Garden

1 Answer

Hi I just bought a 1987xj900 without the fuel tank connected,it has 3 pipes facing up coming from the back of the carbs and 3 smaller pipes facing down,I presume the down pipes are for air and vapour but...

from memory
a fuel line( runs to a fitting on carbs which feeds all carbs with a common tube)
a vacumn line to opperate the fuel tap(slightly larger diameter comes off the manifold)
a tank breather line

Jul 09, 2011 | Yamaha XJ 900 F Motorcycles

1 Answer

Where is the fuel pump located?

The fuel pump is inside the tank and is accessed from the top of the tank, so you'll have to remove the tank.
Disconnect the battery.
Remove the filler cap.
Drain the fuel from the tank(retighten drain plug to 20Nm - 14lbf after draining)
Remove the right hand rear fender liner.
Remove the tank under cover fixing bolts and remove the cover.
Disconnect tank wiring.
Disconnect the piping at the tank(Fuel filler, evap hoses, air breather hose).
The fuel supply and release lines are quick release. Supply has 2 tabs that need to be squeezed before the pipe can be pulled apart. The return line has a square block that needs to be pressed to split the line. The fuel lines may have residual pressure inside so cover with a cloth when releasing so you dont end up with fuel in your eyes. When refitting lightly coat with oil to aid assembly.
You can now undo the tank fixing bolts and remove the tank.(When refitting tighten to 36 Nm - 27lbf)
Once you have the tank on the ground you can remove the pump by undoing the fixing screws and withdrawing it from the tank.

Nov 08, 2010 | 2000 Isuzu Rodeo

1 Answer

How do i hook up my gas tank to my carbs? i dunno where the plug on the the spickets go to where they hook up on the carbs. is there a full diagram where it shows feul lines going from tank spickets to...

There should be 4 open ports on the carb 1 smaller ones towards the right carb to the front which is the vacuum hose that connects to the smaller connection on the petcock, then the 2 larger holes which are side by side 1 on each carb, they are the breathers, the fuel line goes to the one that is the highest connected by the fuel pipe which you can see going through it and then that connects to the larger hookup on the fuel petcock. The breather hoses just hang down but watch where you put them because they tend to **** in dirt if they are closer to the ground try facing them under the seat away from where dust could be although its pretty unavoidable.

Sep 17, 2010 | 1982 Suzuki Gs 550 L

1 Answer

Removing tank

Disconnect battery ground cable. Loosen fuel filler cap. Support underneath of the fuel tank protector Disconnect evaporative fuel hose at the canister. Disconnect fuel feed hose and fuel return hose near the fuel filter. Plug both ends of the fuel hoses to prevent fuel leakage. Disconnect air breather hose and fuel filler hose at the fuel filler neck. Cover fuel hose to prevent any dust entering. Remove the four fuel tank assembly fixing bolts at four corners of the tank. Let down the tank and disconnect the wiring connectors Remove fuel tank assembly along with protectors Remove retaining cover and roll over & float valve along with the evaporative fuel hose and pipe Remove fuel pump and sender assembly by removing the snap ring with the fuel hoses Remove protectors by removing the six fixing bolts

Jun 12, 2009 | 1999 Isuzu Rodeo

2 Answers

Breather pipe

one's a breather and one is petrol overflow (i think?) they will both go down to near the left foot and come out at the end with another pipe...the coolant overflow.

Dec 14, 2008 | 1995 Honda CBR 600 F(3)S

Not finding what you are looking for?
1994 Honda CBR 600 F(2)R Logo

Related Topics:

238 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4825 Answers


Level 3 Expert

79186 Answers


Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides