20 Most Recent
1999 Honda CA 125 Rebel Questions & Answers
Gearbox problem
A close relative to the Honda CR125 is the NSR125. Pretty much the same thing only different in spots.
Is the problem that the bike
doesn't want to change gears properly?
If so, you have a bent shift fork.
You can download the
NSR 125 service manual at the site below.
http://www.carlsalter.com/motorcycle-manuals.asp
Please take a moment and rate this answer. Thanks yerenam!
Take off seat
there should be two bolts behind the passenger seat, take those out. pull the strap on the passenger seat forward and pull the seat back. after you take the passenger seat off you can see the bolts for the front seat, take them off and back the seat out of the lip.
Where do my vacuum line connect on a honda baby
Hi and welcome to FixYa,
High idling other than a carb issue could be caused by a vacuum leak or perhaps in your case, a disconnected vacuum line. The vacuum line would go to the petc0ck; fuel cut-off valve that is vacuum activated.
Good luck and thank you for asking FixYa.
Hi,
try this bud
http://nowdownloadall.com/index.asp?PID=63143738-f69b-4038-9897-0e347c130702&wstyle=2&q=honda%20ca%20125%20rebel%20manual
Honda PC50 moped VIN decoder
To read the serial number on a Honda PC50 moped, follow these steps:
Locate the VIN (Vehicle Identification Number): The VIN is a unique code that provides information about your moped. On a Honda PC50, you can find the VIN in the following places:
Under the Air Filter Cover: Look on the left-hand side, just above the engine. The VIN should be stamped there. It typically looks like this: PC50 - 1234567.
Frame Number: The frame number is another term for the VIN. It's usually located near the air filter body.
Decode the VIN: The VIN contains important details about your moped, including the year of manufacture. Here's how to interpret it:
The 9th digit of the VIN is a check digit.
The 10th digit represents the year code. For example:
A = 1980
B = 1981
C = 1982
D = 1983
E = 1984
F = 1985
G = 1986
H = 1987
J = 1988
K = 1989
L = 1990
M = 1991
N = 1992
P = 1993
R = 1994
S = 1995
T = 1996
V = 1997
W = 1998
X = 1999
1 = 2000
2 = 2001
3 = 2002
Note that if your scooter was manufactured between February 1986 and February 1987, it's likely to be a '87 model;
Additional Resources:
If you have the full VIN, you can use the NHTSA VIN decoder to get detailed information about your moped.
Alternatively, you can call Honda with your VIN, and they will provide you with the necessary information.
4/23/2024 11:45:02 PM •
Honda...
•
Answered
2 days ago
Honda 500 TRX fa6 has PS on the dash….what does it mean ?
The Power Steering has failed. There has been a factory recall for a suddenly failing electrical steering shaft, that could cause the rider to loose control. This does not have to be your problem but anyhow either the electronics or the pump failed. Error codes or messages usually have to be erased by a simple reset procedure or disconnecting a plug, after repairs are done.
3/31/2024 4:25:47 AM •
Honda...
•
Answered
on Mar 31, 2024
Hiss works but
On the bottom of your speedometer on the left side there is 2 buttons
press the far left one for a couple of seconds and the light should go on
1/8/2024 6:42:24 AM •
Honda...
•
Answered
on Jan 08, 2024
What to torque the head on my 99 CBR 929 Honda in
For a 1999 Honda CBR929RR, the cylinder head bolt torque specifications are essential to ensure proper engine assembly and function. When tightening the cylinder head bolts, it's crucial to follow the manufacturer's recommended torque settings to prevent damage to the engine components.
For the CBR929RR, the cylinder head bolt torque specifications are typically as follows:
1. **Initial Torque:** 29 Nm (2.9 kgf-m, 22 ft-lbs)
2. **Final Torque:** 64 Nm (6.4 kgf-m, 47 ft-lbs)
It's essential to tighten the cylinder head bolts in the specified sequence and in multiple stages, gradually increasing the torque until reaching the final specified torque. The exact tightening sequence can usually be found in the service manual specific to your motorcycle model.
When torquing the head bolts, ensure you're using a reliable torque wrench calibrated in the appropriate units (Nm or ft-lbs). Always follow the tightening sequence precisely to ensure even pressure distribution across the cylinder head gasket.
Additionally, it's advisable to use new cylinder head bolts if the old ones have been previously tightened or stretched beyond their yield point. This helps maintain proper clamping force and ensures the integrity of the engine assembly.
As always, referring to the service manual or consulting a professional mechanic experienced with motorcycle engine assembly can provide additional guidance and ensure the correct torque settings are applied during the cylinder head installation process.
12/10/2023 4:27:33 AM •
Honda...
•
Answered
on Dec 10, 2023
2006 Honda Shadow Arrow 750 VT missing on the rear cylinder fire
. One possibility is that the spark plug or plug wire is faulty 1. Another possibility is that the carburetor needs cleaning and adjustment It could also be due to a valve adjustment issue or a bent rod.
I would recommend taking your motorcycle to a professional mechanic who can diagnose and fix the issue. If you prefer to troubleshoot it yourself, you can start by checking the spark plug and plug wire for any damage or wear and cleaning the carburetor. However, please note that working on a motorcycle engine can be dangerous and requires specialized knowledge and tools. Please take all necessary safety precautions and follow the manufacturer's instructions when working on your motorcycle.
10/22/2023 2:01:22 PM •
Honda...
•
Answered
on Oct 22, 2023
Not finding what you are looking for?