Question about 1995 Ford F350

1 Answer

F-350 I have a 1995 f-350 . the dtc# P0476 & P0562 are the codes on the superchip reader. please help with info on these codes. think you, cg

Posted by on

  • csgriffith Jul 09, 2008




1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 373 Answers

OK. 1995 Ford 350 " Diesel " 7.3 l

P0476 This code refer to Exhaust Pressure Control "EPR" "Valve. Performance, or ""exhaust back pressure sensor "EBP"
P0562 This code refer to System voltage too low.

I hope this this information help.

Posted on Jul 04, 2008

  • Juan Guillen Jul 09, 2008

    HI. Yes, I can give to you some tips.

    1- As normal check the condition of the batteries,

    For the P0562, and the battery terminal for corrosion damaged or just loosing connections. Ground and positives,

    2 - P0476 , You need to visualy inspect for butterfly tang, with key on engine off, if tang is open,

    Check for any exhaust restriccion, muffler, catalystic converter,

    No restriccion and no leaks....

    The valve use a linkage, check good linkage if need adjusted, or are disconnected.

    After that you need a scanner with pid data to check the pid reading.

    OK. all of this is on the throttle body. the butterfly is inner.

    I hope this work but anything letme know, I will help as I can.

    Thank you.



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have innovia obd scaner 3100,but it can't diagnos actros. it say there is no dtc in the computer. what can i do?

Daniel, According to the instructional video below, the code reader is not listed to work on your vehicle, only OBD2 compliant vehicles Domestic, Asian, European sold in United States. Before purchasing another code reader or scan tool make sure it will work and diagnose codes for your vehicle, contact the manufacturer if need be for info. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Innova 3100 Instructional Video
Mercedes Benz DTC Fault Code List

Jul 08, 2016 | Cars & Trucks

1 Answer

I have an 2002 Cavalier Z24. I recently brought it in for repairs. The Technician replaced the ECM/PCM and it's still acting the same way....the alternator just won't charge the battery. it's a new battery...

Hey Joe , The first thing to do would be check for battery voltage on the heavier gage wire on the back of the alternator , if there is no voltage here there is a open circuit ! Which means the fusible link fried . This wire comes from the starter ! This charging system is controlled by the PCM , but they are rarely the problem . Do you have the charge indicator lit on the dash ? Do you have a check engine light on ? This system can set DTC'S - diagnostic trouble codes !
DTC B1328 DTC P0562 DTC P0563 DTC P0621 DTC P0622

Mar 25, 2015 | 2002 Chevrolet Cavalier Coupe

3 Answers

Get codes for my 1997 blazor

Code Reader or Professional Scan Tool
to retrieve codes & other data

Nov 20, 2014 | 1997 Chevrolet Blazer

1 Answer


Make sure your 12V grounds to engine and chassis are good.

Apr 11, 2017 | Mazda RX8 Cars & Trucks

1 Answer

My battery light went on, on. My 2003 GMC ENVOY, the message board said "battery not charging" .....I took it to autozone and they said I had a bad alternator which is why it would say battery not...

The charging system on your vehicle is Computer controlled . called ( smart charging system )
The IPC illuminates the battery not charging indicator in the driver information center when the following occurs:
• The PCM detects that the generator output is less than 11 volts or greater than 16 volts. The IPC receives a class 2 message from the PCM requesting illumination.
• The IPC determines that the system voltage is less than 11 volts or greater than 16 volts. The IPC receives a class 2 message from the body control module (BCM) indicating the system voltage.

Do you know what DTC'S - diagnostic trouble codes are ?
DTC B1327
DTC B1328
DTC P0562
DTC P0563
DTC P0621
DTC P0622
DTC P1633
DTC P1634
DTC P1637
DTC P1638
These codes are all associated to charging system problems .

Battery light lit on the instrument cluster ?

Are You Smarter Than Smart Charging System MOTOR

Oct 27, 2017 | Cars & Trucks

1 Answer

Code p0562 on a 2004 Kia Spectra

Hi there:

P0562 KIA - System Voltage Low
The battery supplies electricity to the ECM even when the ignition switch is OFF. This electricity allows the ECM to store data such as DTC history, freeze frame data, fuel trim values and other data. If the battery voltage falls below a minimum level, the ECM will conclude that there is a fault in the power supply circuit. The next time the engine starts, the ECM will turn on the MIL and a DTC will be set.

Possible causes:

- Loose or missing alternator drive belt
- Faulty alternator
- Battery defective
- Open or short system voltage circuit

Tech notes:
Start by recharging or replacing the battery.

The P0562 code is detected when the battery voltage detected by the ECM is less than a calibrated value

- Engine Light ON (or Service Engine Soon Warning Light)
- Slow engine start
- Low battery power

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jul 20, 2012 | 2000 Hyundai Accent

1 Answer

1999 pontiac grand am not charging

Diagnostic Test Code (DTC) U1000 has a generic description of "Class 2 Serial Data Link Malfunction".
DTC U1064 has a description of "Loss Of Communication With Body Control Module (BCM)"
These codes can be caused by a malfunctioning charging system and should be ignored for now.

DTC P0562 has a description of "System Voltage Low". So this code basicly is only verifying that you indeed have a no-charging problem and that the other codes are most likely also caused by low system voltage.

Although these codes do verify that you have a charging system problem, they are useless in finding out exactly what is wrong with your charging system.

You will need a scan tool that is capable of 2-way communications with the PCM and performing system tests. you will also need a digital multimeter to test the system as you command the generator circuits on with the scanner. If your scanner can do this, let me know and I will get you the troubleshooting instructions for your vehicle. Otherwise, you will have to take it to someone who is properly equipped to diagnose your charging system.

Dec 21, 2011 | Cars & Trucks

2 Answers

I have an 1999 ford f350 7.3 powerstroke. I'm having white smoke coming out of the exhaust, I had trouble shot the vehicle the codes are DTC 04 p0562, DTC 03 p1670, DTC 02 p0603 and DTC 01 p0344. I...

P0344 = cam position sensor error
P0603 = Internal control module keep alive memory error.
P1670 = communication error between PCM and IDM
P0562 = system voltage low

My guess is you probably have some wiring issues but it's hard to tell exactly where.

May 16, 2011 | 1999 Ford F350 Regular Cab

1 Answer

Po 562

OBD-II Diagnostic Trouble Codes (DTC)

DTC Codes - P0500-P0599 - Vehicle Speed Controls and Idle Control System

P0562 System Voltage Low

Hope this helps.

Jan 31, 2011 | 2004 Dodge Stratus

1 Answer

Truck has been running great,turned truck off , restarted it to notice a rough idle then check engine light came on, i had superchips flashpaq on truck ,got to repair shop had to re install ford stock file...

Are we talking about a 7.3L diesel? If so, I have seen all kinds of trouble started by people flashing their computers with superchips. You are better off with te OEM files in your computer. As for the injector, If we are in fact talking about a 7.3L, you probably need to replace your valve cover gasket. It contains the electrical wiring for the injectors. They like to burn at the connector going into the gasket. Not a cheap fix, either. (About $200 for parts)

Jan 11, 2011 | 1999 Ford Super Duty F 550

Not finding what you are looking for?
1995 Ford F350 Logo

Related Topics:

524 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

78257 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5653 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides