Question about 2000 Ford F150 Flareside SuperCab

Open Question

The parking brake assembly on my 2000 Ford F-150 is toast. I have a Haynes manual, but it doesn't have any pictures to go by. Is there somewhere I can download a picture of the entire assembly?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
csmock132
  • 4669 Answers

SOURCE: Fix chevy 2000 S10 parking brake.

Some times the rotors are hard to remove.(rust) Just soak it with wd40 and use a big hammer or prybar. Try smacking it around the studs, But don't hit them. If you smack the part of the rotor that the regular service brake rides on you will warp the rotor. Just keep trying, you'll get it. Also if you mess up the rotor they really aren't that expensive to replace. Plus your old one is likely wore out anyways.

Posted on Apr 05, 2009

Ad
  • 130 Answers

SOURCE: How do I adjust the parking brake?

Loosen the cable nut at the rear brake, pull the cable until the tension is tight, then tighten the cable nut. Since the parking brake only operates on the rear brakes, your rear pads may be too worn causing the parking brake not to hold. Check the pads first to see if they need to be replaced. Also, the parking brake cable can stretch or break over time. Verify that isn't case since you may need to install a new cable rather than adjust it.

Posted on May 03, 2009

alicantecoli
  • 22246 Answers

SOURCE: where is the Pcv valve

haynes manuals ?? you having a LAUGH under the radio

Posted on Nov 12, 2008

  • 1348 Answers

SOURCE: Mustang parking brake won't release tension on rear brakes

since the new pads are alot thicker than the old ones,the brake needs to be set properly.
something is not right for sure.
the retainer for the park brake cable may be not in the right spot.there is two places it can fit.

Posted on May 23, 2009

c17hydro
  • 2984 Answers

SOURCE: 2000 Ford Taurus. How do I change a ball joint?

Lower Ball Joint Inspection

  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Raise and support the vehicle.
  3. Prior to carrying out any inspection of the ball joints inspect the wheel bearing.
  4. Have an assistant pull inward and outward on the top and the bottom tire. Mount a suitable dial indicator and measure the movement between the ball joint and the lower arm. If the movement is at or exceeds 0.03 in. (0.75 mm) install a new ball joint.
167f4af.gif

Removal & Installation To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Remove the knuckle from the front suspension.
  3. Remove the snap ring from the ball joint.
  4. Press the ball joint out of the knuckle with a suitable ball joint press and adapters.
656c3d7.gif

Posted on Jul 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The linkage are hooked up but the car still want go into park,a 2000 Taurus


Do you have floor console shifter ?
Shift Interlock System A brake/shifter interlock system consists of the following:
  • ignition switch (11572)
  • brake pedal stoplight switch (13480)
  • brake shift interlock module
  • brake shift interlock solenoid assembly (attached to key interlock assembly)
  • necessary wiring
On floor-shift vehicles, the ignition/shifter interlock cable (3F719):
  • locks the floor shift transaxle range selector lever in the PARK position when the ignition switch is in the LOCK position.
  • requires the floor shift transaxle range selector lever to be in the PARK position to turn the ignition switch to the LOCK position.

May 04, 2015 | 2000 Ford Taurus

1 Answer

Emergency brake cable installation


Purchase a Haynes repair manual for your vehicle. It should have step by step instructions with pictures showing how to replace a park brake cable.

Good luck, I hope this helps!

Apr 17, 2014 | 1995 Ford Econoline

1 Answer

I have to replace all askspecs of my parking brakes on a


lever kit works the emergency (mechanical) brakes..the parts tore should have an assembly picture of this setup..there is also an exploded parts view of this ..it should show how it goes..

Dec 14, 2013 | 2000 Ford Expedition

1 Answer

How do I get the rear drums off a 2000 Ford focus. I removed the spindle nut,


2000 Ford Focus Drum Removal ProcedureIf removing the drum to service the rear brakes: (note, do not remove hub retaining nut for this procedure)
1. Raise and support vehicle
2. Release the parking brake
3. Remove wheel and tire
4. Disconnect wheel speed sensor wiring harness from wheel knuckle and floor panel.
5. Remove 4 wheel spindle attaching bolts, then the wheel hub and drum assembly from vehicle.
6. Reverse procedure to install noting the following:
a. Torque wheel spindle retaining nut to 49 ft. lbs.
b. Torque wheel/tire assembly to 94 ft. lbs.
2000 Ford Focus Drum Replacement ProcedureIf replacing the drum and wheel bearing assembly:
1. Raise and support vehicle
2. Release the parking brake
3. Remove wheel and tire
4. Remove center dust cap.
5. Remove hub retaining nut.
6. Remove drum and hub assembly. Ensure wheel speed sensor ring is not damaged when removing drum/hub (if equipped).
7. Reverse procedure to install noting the following:
a. Inspect and clean wheel speed sensor ring if equipped.
b. When tightening hub retaining nut, rotate the hub assembly in counterclockwise direction.
c. Torque hub retaining nut to 173 ft. lbs.
d. Torque wheel/tire assembly to 94 ft. lbs.
e. Adjust parking brakes as necessary.


Jul 05, 2011 | 2000 Ford Focus

1 Answer

I need a manual to see how to install back brake assembly on shoes on drum please


I Use the Haynes Repair Manual on my vehicle but a Chilton's will also have a picture and diagrams of the rear wheel brakes.

Feb 20, 2011 | 2000 Dodge Stratus

1 Answer

I'm replacing my rear brake shoes on my 2001 chevy venture,i've assembled new parts and what has been happening is when i push on the brake pedal the adjuster actuator and actuator spring keep popping off...


Parking brake lever on leading shoe (end of retractor spring in its hole on the leading shoe). Make sure the the adjuster screw assembly is engaged properly with the leading shoe (also, engaged with the parking brake lever). Adjuster actuator installed on the trailing shoe (also, engaged with the adjuster screw assembly). After inserting the retractor spring in its hole on the trailing shoe, insert actuator spring in its hole (just below wheel cylinder) in leading shoe and stretch across and connect it to the adjuster actuator. Adjust star wheel to get shoes close to drum. Reinstall drum (shoes close with no rub). Reinstall wheel. Push brake pedal for final adjustment. Test forward. Test Backwards. If everything is in the correct place, nothing should pop off. I hope you have a before picture. Haynes manual has good pictures. I own a 2002 Pontiac Montana, but a family member has taken it out of town. My info is from the Haynes manual. I replaced the brake shoes a couple years ago.

Feb 20, 2011 | 2001 Chevrolet Venture

3 Answers

2008 f150 shakes when braking, chaged brakes and


makes no sense other than maybe the anti lock system is messing up

Mar 28, 2010 | 2008 Ford F-150

1 Answer

Heater core for a Ford 2000 F-150 5.4 4x4 had been


There is a Haynes Manual available for your vehicle @ most large Auto Parts stores. It covers how to do this. $25.00 for book.

Feb 03, 2010 | 2000 Ford F150 Flareside SuperCab

1 Answer

1979 FORD F-150 4X4, NEED TO DISASSEMBLE FRONT HUBS/FRONT END SUSPENSION


too many details to explain here.find a HAYNES REPAIR MANUAL or equivelent covering your vehicle.step by step instructions w/ pictures.

Sep 22, 2009 | 1981 Ford F 150

2 Answers

'93 Ford Econoline 150 E-brake pedal teeth gone!


Try http://fordpartscenter.net , I found the parking brake control for my 95 E350 on this site, they also had the cables.

Jul 15, 2009 | 2000 Ford Econoline

Not finding what you are looking for?
2000 Ford F150 Flareside SuperCab Logo

Related Topics:

601 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...