3certified electronics technician
kirtec auto posted an answer for this 2005 Nissan Altima:
"Is it a series of three beeps?then the car thinks the key is in the ignition and you need..."
kirtec auto
kirtec auto posted an answer for this 1996 Nissan Maxima:
"Check the alternator output. It should be 14 volts. You could have a bad PCM . As the..."
kirtec auto
kirtec auto posted an answer for this 2005 Nissan Maxima:
"Disconnect the fan and apply 12volts to it and see if runs on high or measure the voltage..."
kirtec auto
kirtec auto posted an answer for this 2005 Audi A4:
"The sensor itself is not hard to replace but the issue is more likely a streched timing..."
kirtec auto
kirtec auto posted an answer for this 2000 Dodge Durango:
"only 3 possibilties. both low beam bulbs are burnt out,the light switch is no good or the..."
kirtec auto
kirtec auto posted an answer for this 2001 Honda Odyssey:
"you have multiple misfire po300 and cylinder 5 po305 misfire.the misfire is causing the..."
kirtec auto
kirtec auto posted an answer for this 2002 Honda Accord:
"if replacing the high beam bulbs do not fix the DRL issue ,see my tip under 2001 to 2005..."
kirtec auto
kirtec auto posted an answer for this 2006 Honda Civic:
"Please check my tip written for this problem. It is caused by bad soldering on the daytime..."
kirtec auto
kirtec auto wrote a tip for Honda Cars & Trucks:
"Symptoms are: The daytime lights do not work,the DRL light is on. The high beam or low..."
kirtec auto
kirtec auto posted an answer for this Lexus Cars & Trucks:
"the starter contacts inside the starter are probably worn out.This is a very common fault..."
kirtec auto
kirtec auto posted an answer for this 2000 Ford Expedition:
"there is one on the dash on the driver side .there is another inside on the driver door..."
kirtec auto
kirtec auto posted an answer for this 2004 Mitsubishi Outlander:
"You can buy slider pin bushing kits for the caliper.check that it is the caliper and not..."
kirtec autokirtec auto posted an answer for this 2004 Mitsubishi Outlander:
"1st i would make sure that it is indeed the calipers and not the stabilizer bar end..."
kirtec autokirtec auto posted an answer for this Chevrolet Cars & Trucks:
"for some reason the timing is way off .that engine has a vacuum advance for ignition..."
kirtec autokirtec auto posted an answer for this Cars & Trucks:
"it is usually mounted on the transmission."
kirtec autokirtec auto posted an answer for this Toyota Cars & Trucks:
"it is quite difficult.because it is an internal water pump driven by the timing belt."
kirtec auto
kirtec auto posted an answer for this 1993 BMW 325:
"i would have the battery loadstested first and the starter current draw tested before..."
kirtec autokirtec auto posted an answer for this 2005 Nissan Maxima:
"The 2005 altima 2.5 175 hp 4 cylinder CVTC and the 250 hp 3.5 VQ35DE V6 both use timing..."
kirtec auto
kirtec auto posted an answer for this 2008 Jeep Commander 3.7:
"most mirrors have push pins holding the top of the glass to the movable backing plate and..."
kirtec auto
kirtec auto posted an answer for this 2003 GMC Yukon XL:
"It could be the starter has a dead spot,the battery voltage is weak,the ignition switch..."
kirtec autokirtec auto posted an answer for this 2003 GMC Yukon XL:
"bad gauge in cluster.. test with an oil pressure gauge to confirm. a good scanner or gm..."
kirtec auto
kirtec auto posted an answer for this 2004 GMC Yukon:
"common problem .easy fix"
kirtec auto
kirtec auto posted an answer for this 1996 Plymouth Voyager:
"the 96 97 98 caravan has an issue with bad instrument clusters where the speed is..."
kirtec auto
kirtec auto posted an answer for this 1996 Mercury Grand Marquis:
"check that the fuel pressure is within spec. also the EGR port on the 4.6 litre can get ..."
kirtec auto
kirtec auto posted an answer for this 2002 Chrysler Sebring:
"the camshaft sensor is very common on chrysler. the magnet becomes weak and since it is a..."
kirtec auto
kirtec auto posted an answer for this 1998 Mercury Mountaineer:
"1309 code is misfire monitor failure the po340 is a failed camshaft sensor causing it."
kirtec auto
Cars & Trucks 1091 answers
Televison & Video 111 answers
Car Audio & Video 62 answers
Audio Players & Recorders 61 answers
Radio Communications 4 answers
Electronics - Others 2 answers
Music 2 answers
Irons 1 answer
Vacuums 1 answer
Dryers 1 answer
