The tire pressure warning needs to be reset and i dont know how

You can't reset the tire pressure warning light (TPMS), when the pressure is adjusted or the sensor replaced (if the warning is false) the light will go out, there is no reset. Check the air pressure in all the tires, they should be about 34 PSI all around.

By operating the tire pressure warning system reset switch, tire pressure warning system ECU can be set to issue a warning at an inflation pressure that corresponds with the type of tires.
Operate the tire pressure warning system reset switch only after the inflation pressures of all 4 tires have been adjusted on the vehicle.
To initialize the system, press and hold the tire pressure warning system reset switch for 3 seconds or longer with the power switch turned IG-ON. When starting the initialization, the tire pressure warning light blinks 3 times at 0.5 Hz.
During the initialization, the tire pressure warning system valve & transmitter measures the inflation
pressure of the tires, and registers the signals that are transmitted into the ECU at a frequency of 1 per
minute. The initialization process is completed when the signals from the tires have been received.
Once the tire pressure warning system reset switch has been pressed, do not turn the Ignition switch OFF for a few minutes.

By operating the tire pressure warning reset switch, the tire pressure warning ECU can be set to issue a warning at an inflation pressure that corresponds to the standard pressure of tires .Therefore, you must set the warning threshold to the proper value in order to comply with the local regulations .Operate the tire pressure warning reset switch only after the inflation pressures of all tires have been adjusted on the vehicle.To initialize the system, press and hold the tire pres- sure warning reset switch for 3 seconds or longer with the ignition switch in the ON position. When the system receives the
initialization signal, the warning light blinks 3 times (1 second on, 1 second off). During initialization, the tire pressure warning valve and transmitter measures the inflation pres sure of the tire, and registers the signals that are transmitted into the tire pressure warning ECU at a frequency of once per minute. The initialization process is completed when signals from all the tires have been received. It takes a few minutes .

Tire size Inflation Front Inflation Rear
P 195/65 R15 89S 30 psi 30 psi
195/65 R15 91H

P 205 /55 R16 89H 32 32 psi
P 215/45 R17 87W
205/55 R16 91V

Charge you extra for doing what should have been done? you will need the tire sensors relearned. this is always included with installation. I dont know who you are dealing with? dealer?. I dont think you can reset the sensors without a scanner.

There are 4 key ignition settings: Off, Acc, On, Start Turn key to the On position, quickly press the gas pedal 3 times, then turn key clockwise to Start position and actually start the car. You'll hear it chime at you and the change oil indicator light will flash and disappear.

The tire light....Have you checked all your tires for prper air pressure? including the spare? If they all have the maunfactures recomended PSI. Remove the negitive post from the battery for 20 min. to rest puter. If that dont work you have a faulty TPMS on a tire need a new one. Hope this helps

Your tire pressure monitor needs to be reset whenever you change or rotate your tires...

1. check and make sure that your tires are inflated to the correct pressure

2. turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns off and then release the switch.

3. now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

4. initialization is *not* completed until driving at the vehicle speed of 19 mph or over for more than one hour. the tire pressure monitoring starts when initialization is completed.

1. check and make sure that your tires are inflated to the correct pressure

2. turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns off and then release the switch.

3. now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

4. initialization is *not* completed until driving at the vehicle speed of 19 mph or over for more than one hour. the tire pressure monitoring starts when initialization is completed.

If your vehicle has similar controls like my 2006 Sequia. put the ignition in the ON position... then press the Tire Pressure Monitor Reset button (it is located on the dashboard button right beneath the streering wheel column).. press it for 4 to 5 seconds till you see the pressure monitor light come on and then go off. That should reset the system.

Reset the tire pressure warning, same as you would any service issue. Insert key in ignition, hold wrench button and min button, then start engine.

this would be a low tire symbol have you tire pressure check it will come on when one off your tires get a little low. the light will reset itself after the proper tire inflation is put in ..thanks for choosing fixya