Replace automatic transmission shift cable - Cars & Trucks

Question edited for clarity and add maker.
Question moved to model category.

Shift Cable Repair procedures - Automatic Transaxle Control ...

helantraad.com https://www.helantraad.com > shift_cable_repair_proc...
1. Air cleaner assembly and air duct. · 2. Battery and battery tray. · 3. Remove the nut (A) from the manual control lever. · 4. Remove the shift cable (B) from ...

2008 Hyundai Elantra Automatic Transmission Shifter Cable

Hyundai Parts Pro https://www.hyundaipartspro.com > Automatic-Trans...
Automatic Transmission Shifter Cable. 2008 Hyundai Elantra. Genuine Hyundai Part - 467902H100 (46790-2H100). Ships from Hyundai Parts Pro.
Rating: 4.8 · ‎361 reviews · ‎$105.19

..

SOLVED: Toyota highlander shift lever moves freely but - Fixya

https://www.fixya.com > ... > Toyota > Highlander
Sept 2, 2019 - First off, set the parking brake, raise vehicle so you can get under it. Remove the shift linkage from the transmission and manually move the shift lever to ...
I have a 2002 Toyota Echo. The end of the gear - Fixya
Oct 24, 2008
SOLVED: My 2001 toyota highlander will not shift into - Fixya
Sept 1, 2019
Transmission gear shift got stuck in Drive not able to move
Nov 20, 2019
Toyota sequoia gear shift lever broken - Fixya
Nov 16, 2019
More results from www.fixya.com

2001 V6 Highlander - Transmission Cable issue? - Toyota ...

https://www.toyotanation.com > forum > 816897-2001-...
Jun 9, 2014 - The shift lever moves VERY freely, but will not engage or come out ... It's probably a broken shifter cable , the joint at the transmission ...

Car in park shifter will move through gears but wont shif...

https://www.yourmechanic.com > Questions
Jul 13, 2016 · 1 answer
From what you've described, it sounds like the shifter cable came off at the transmission or the shifter. I'd suggest checking the shift ...

Automatic Transmission Problems Shifting Gears - Ira Toyota ...

https://www.toyotaofmanchesternh.com > automatic-tra...
One reason why an automatic transmission isn't shifting into gear has to do with the fluid. If it's not at the right level or the incorrect type has been used, ...

It definitely sounds like you have a bad shifter cable. Not a very expensive part, but can be a pain to get changed.

Automatic Transmission Shift Lock Control System
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
• The automatic transmission shift lock control solenoid
• The automatic transmission shift lock control switch
With the ignition in the ON position, voltage is supplied to automatic transmission shift lock control switch. Voltage flows through the normally closed contacts of the automatic transmission shift lock control switch to the automatic transmission shift lock control solenoid. The automatic transmission shift lock control solenoid is permanently grounded. This energizes the automatic transmission shift lock control solenoid causing the transmission shift lever to be physically locked in the PARK position. When the brake pedal is pressed the contacts in the automatic transmission shift lock control switch open, de-energizing the automatic transmission shift lock control solenoid. This allows the shift lever to be move out of the PARK position.

Circuit Description
The transmission range (TR) switch is part of the park/neutral position (PNP) and back-up lamp switch assembly, which is externally mounted on the transmission manual shaft. The TR switch contains four internal switches that indicate the transmission gear range selector lever position. The powertrain control module (PCM) supplies ignition voltage to each switch circuit. As the gear range selector lever is moved, the state of each switch may change, causing the circuit to open or close. An open circuit or switch indicates a high voltage signal. A closed circuit or switch indicates a low voltage signal. The PCM detects the selected gear range by deciphering the combination of the voltage signals. The PCM compares the actual voltage combination of the switch signals to a TR switch combination chart stored in memory.

These are all electronically controlled , yur best bet would be to take your vehicle to the dealer .

replace transmission more likely cable need replacing old shift cable stretched more likely.

Automatic Transmission Shift Lock Control Description and Operation
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of thew following components:
• The automatic transmission shift lock control solenoid
• The body control module (BCM)
• The powertrain control module (PCM)
With the ignition in the ON position, battery positive voltage is supplied to the automatic transmission shift lock control solenoid. The automatic transmission shift lock control solenoid receives a ground from the BCM. When the automatic transmission shift lock control solenoid is energized, the shift lever mechanically locked in the PARK position. When the driver presses the brake pedal the PCM sends a class 2 serial data message to the BCM. The BCM turns OFF the ground control circuit and this de-energizes the automatic transmission shift lock control solenoid. When the automatic transmission shift lock control solenoid is de-energized, the shift lever may be moved out of the PARK position. The BCM determines transaxle shift lever position through a class 2 serial data message from the PCM. The PCM receives inputs from the park/neutral position switch and determines shift lever position. When the BCM receives this information and determines that the shift lever is out of the PARK position, the automatic transmission shift lock control solenoid ground is opened.

Do you know what a DTC is ? Diagnostic trouble code !

DTC B2708
The body control module (BCM) controls the automatic transmission shift lock control solenoid. Positive voltage is supplied via the ignition 1 voltage circuit to the automatic transmission shift lock control solenoid. The BCM controls the ground circuit of the automatic transmission shift lock control solenoid . When the brake pedal is depressed, the BCM removes the ground allowing the solenoid to disengage. This action allows the vehicle to be shifted out of the PARK position.
Conditions for Running the DTC
DTC B2707

Your best bet mite be to have a qualified repair shop check it .

For Automatic transmission problem,click the link below:---- Automatic transmission troubleshooting:----

http://howtobyme.blogspot.com/2011/11/automatic-transmission-will-not-go-into.html

---------
Automatic transmission shift lever issues?-------

http://technoanswers.blogspot.com/2012/01/automatic-transmission-shift-lever-hard.html

-----------
AUTOMATIC TRANSMISSION FLUID LEVEL? --

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-automatic-transmission.html

--------------

AUTOMATIC TRANSMISSION FLUID AND FILTER?

http://schematicsdiagram.blogspot.com/2011/07/how-to-change-automatic-transmission.html

-----------
Transmission fault light on car dash?

http://schematicsdiagram.blogspot.com/2011/12/transmission-fault-light-on-car-dash.html

--------
Transmission shifting problem?

http://schematicsdiagram.blogspot.com/2012/01/transmission-shifting-problem-on-toyota.html

--------
Transmission Slips out of 2nd gear?

http://repairhelpcenter.blogspot.in/2012/02/transmission-slips-out-of-2nd-gear.html

-----------
OD light flashing and transmission fluid leaking?

http://repairhelpcenter.blogspot.in/2012/02/od-light-flashing-and-transmission.html

----------
Why Transmission fluid leaks near radiator?

http://repairhelpcenter.blogspot.in/2012/02/transmission-fluid-leaks-near-radiator.html

----------
Transmission fluid leaking?

http://technoanswers.blogspot.in/2012/02/ford-windstar-transmission-fluid.html

-------------
****** wont go in reverse?

http://technoanswers.blogspot.in/2012/02/dodge-neon-wont-go-in-reverse.html

-------------
Automatic transmission will not go into reverse?

http://technoanswers.blogspot.in/2012/02/dodge-automatic-transmission-will-not.html

----------
Transmission is making buzzing noise?

http://technoanswers.blogspot.in/2012/02/transmission-is-making-buzzing-noise.html

-----------

This will help.

Thanks.

What trans? AOD? This is 1992 F Series, all I have.

Shift Controls, Automatic Transmission The transmission shift control linkage or cable transfers the transmission operating mode from the selector lever to the transmission. The indicated transmission position on the steering column is transferred to a shift lever on the bottom of the steering column. On vehicles equipped with cable-operated shift systems, the indicated position of the transmission selector lever is transferred to the transmission through the shift cane, then to the cable, and down to the transmission manual shift lever at the transmission. On vehicles equipped with shift rod assemblies, the rod transfers the indicated transmission selector level position through a bell crank assembly to a control rod. The control rod transfers the indicated position to the transmission assembly.
----------------------------------------------
Automatic Transmission Manual Linkage Adjustments

1. With the engine stopped and the parking brake applied, place the transmission selector lever at the steering column in the D (DRIVE position) for C6 applications and in the (D) (OVERDRIVE position) for AOD and E4OD applications, and hold against the D or (D) stop by applying a three-pound force to the selector lever knob.

1. Loosen the shift rod adjusting nut at point A. Refer to the following illustrations.

1. Shift the manual lever at the transmission into the (D) (overdrive) position for E4OD, by moving the lever all the way rearward, then forward two detents.

1. With the selector lever and transmission manual lever in the(D) position, tighten the nut at point A to 17-24 Nm (12-18 ft-lb) torque. Use care to prevent motion between the stud and rod.

1. Remove the three-pound force from the steering column selector lever knob.

1. Operate the shift lever in all positions to make certain that the manual lever at the transmission is in full detent in all gear ranges. Re-adjust the linkage if required.

1. On F-Super Duty Chassis Cab and Motorhome and Commercial Chassis recheck for correct operation of the automatic transmission selector indicator (PRN(D)21). Refer to Section 11-04A, Steering Column, Shift Rod Within Tube. CAUTION: Under no circumstances will it be permissible to adjust linkage in any position other than the(D) position for E4OD applications.
   

---------------------
Automatic Transmission Shift Cable Adjustment

1. From inside the vehicle, place the column shift select lever in the DRIVE position (C6) of the OVERDRIVE (AOD and E4OD). Hang a three-pound weight on the selector lever.

1. Raise vehicle on a hoist.

1. Remove the shift cable from the transmission lever ball stud.

1. Pull down the lock tab on the shift cable body.

1. Position the transmission shift lever in the DRIVE position (C6) or the OVERDRIVE position (AOD and E4OD). This is three detents from the front-most lever position with the first position counting as one.

1. Connect the cable end fitting to the transmission lever ball stud.

1. Push up on the lock tab to lock the cable in the correctly adjusted position.

1. Lower vehicle down from hoist and remove the three-pound weight from the column shift select lever.

1. After making the adjustment, check for park engagement. Check the transmission control lever in all detent positions with the engine running to make sure correct detent/transmission actions. Readjust if necessary.

The transmission is nearly dry. Add some transmission fluid! Automatic transmissions require oil pressure for the car to move, and if you don't have enough oil in it, it won't build up enough pressure to move the car

is it a manual or automatic...if its a manual you probably forgot to hook up the shift linkage..if its a manual..you probably didnt put the shifter cable from the shifter on top right, so itll pull the gears when you if in and out on to or back and forth..look and see if the cable has too much slack..that hooks up to the transmission(automatic)....