2002 Terios. where is the shaft positioh switch and how to check error code P0705

Code 705 means there is a problem with the transmission selector switch. The engine computer may not know which gear the trans is in. You would need to have a shop check the transmission controls.

code p0705 refers to transmission range(TR)sensor/switch--PRNDL input--circuit malfunction===causes--wiring--TR sensor/switch---ECM/TCM
I would have the TR sensor/switch checked out first and then the TCM module.

P1456 Honda Evaporative Emissions Control System Leakage Fuel Tank


How to Test Transmission Range Switch Honda 2 2L 2 3L

The two codes are unrelated. For the p1456 code, try tightening the gas cap.
For code p0705 (transmission Range Switch), review the info from the second link.

http://www.driveaccord.net/forums/attachment.php?attachmentid=7049&d=1169840715

EOBD II Error Code: P0705
Fault Location:
Multi-Function Transmission Range Switch - Malfunction (PRNDL Input) - Implausible Signal
Possible Cause:
Wiring/Connectors from/to Multi-Function Switch faulty.
Multi-Function Switch faulty.
Engine control module (ECM)/Powertrain control module (PCM)/Transmission control module.

Possible Solutions:
Check Wiring/Connectors from/to Multi-Function Switch.
Check Multi-Function Switch.
Check Measuring Value Blocks.

P0705 Transaxle Range Sensor Circuit Malfunction (PRNDL Input).
The transmisison range switch is located on top of transmission, below the shaft where the shift cable is attached.

P0301 Misfire detected - Cyls. 1-4.
Faulty spark plug or wire

Faulty coil (pack)

Faulty oxygen sensor(s)

Faulty fuel injector

Burned exhaust valve

Faulty catalytic converters

Running out of fuel

Poor compression

Defective computer

This should at least narrow down the isseus.

Best of luck!

OBD Code P1750 = Solenoid Assembly / Manufacturer Control Transmission.

I tell you it is infact your solenoid box assemble is going. What that does is to tell your transmission when to shift into gears. Im assuming your car is having a hard time shifting gears and juts need replace this part.


OBD Code P0705 = Transmission Range Sensor circuit (PRNDL - Input).

I'll check the Neutral Safety Switch. It's located on the shift shaft of the trans, and is a common problem. Also check the wiring leading to the switch, as it is exposed to road grime and has been known to corrode and melt.

Also can review this DTC P0705.

Hope helps.

jeep look under crysler ,as for code you have this is not a crysler jeep code ,its a autozone code so go back and ask them what this code means because its not a genuine manufacturers code ,go and get your money back unless they can give you a proper diagnostics instead of a weekend mechanic boy racer answer

P0705 - Range switch signal incorrect P1529 - MIL on request (from TCM). P0705 tells you there's a problem with the transaxel range switch. Replace it.

Google search for P0705 Rio Error Code and I found this: http://www.kia-forums.com/3g-2006-rio-rio5/39179-error-codes.html Scroll down and the 705 code says: P0705 Transaxle Range Sensor Circuit Malfunction (PRNDL Input). Yer hubby will have to go to Autozone for a Hayes Rio Shop manual and look to see if its something he can fix. If it's in warranty, take it in. TJ

there is a tsb that states a p0705 can be a range switch out of adjustment. To adjust the switch apply park brake, put trans in neutral, remove aircleaner assy, check that the holes line up prefectly in the switch and lever.
I have one in the shop that has some other problem not apperant with the same code.