2000 Nissan Maxima Logo
C
Chris Sherwood Posted on Apr 02, 2014

I have replaced the ignition lock cylinder in my 2000 Nissan Maxima and the car will turn over but not start(no fire)

1 Answer

A

Anonymous

Have you taken ALL your keys to a dealer,
to see if they have to be reprogrammed,
now you have a different ignition cylinder, etc

Sort of guessing here, but that is what my 3 week old
2014 Nissan Frontier Owners Manual say's

I would call the parts dept & ask

5 Related Answers

pal03246

Phil Lovisek

  • 726 Answers
  • Posted on Jul 27, 2008

SOURCE: 96 NISSAN MAXIMA SHUTS OFF UPON DECELLERATION OR WHEN STOPPED

Check to see if the floor on the passanger side is wet. If so, than your A/C drain clogged up and your ECM/computer got flodded by water causing all sorts of funky stuff happening. Right next to the gas pedal is a small cover attached to the computer. It has a clip in it. Remove the clip and tug on the cover. Look at the top of the computer to see if its rusted up. Remove the other side cover also, which is on passanger side floor next to your left foot(if you sitting in passenger seat). and check other side of ECM/computer. Check the ECM for rust on top.
If ALL of that looks OK, than I would replace the switch,(since you are telling me that the key got VERY hot) that is mounted on the back of the ignition cylinder. Its a white round switch that failes after a while especially car beeing 1996, just think about how many times that ignition has been turned ON/OFF since 1996. The mechanism in the switch failes, causing starting issues and funky electrical issues.
Does the car have a remote starter installed?? Or didi it have one in the past?? I have seen companies that install them cause some damage to the harnesses on the switch that is mounted to the back of the igniton cylinder. They use "scotch locks" to connect the remote starter and after a while the connection corrode and cause problems too.
Anyways, check the computer for rust first. Than I would install that switch on back of the igniton. You can buy the switch seperately. You dont need the whole ignition assembly/switch only. Switch is pretty cheap (approx $50 ?). Try that and post results. I would feel pretty good about the switch beeing faulty. I have ssen them fail in the past and that's where your power comes into for the starter circuit.(key getting HOT, switch shorting out, making the key hot and starting the car without the key)

Ad

Anonymous

  • 28 Answers
  • Posted on Apr 12, 2009

SOURCE: 2000 NISSAN MAXIMA TRANSMISSION SLIPPING

If you havent already try to change the transmission filter.Sometimes when the filter gets dirty fluid pressure is comprimised and certain pumps and solenoids which control shifting inside the transmission function off of the fluid pressure,

Anonymous

  • 82 Answers
  • Posted on Apr 19, 2009

SOURCE: AC blower motor resistor Nissan Maxima 2000

yeh its located under the passenger side glove box,its in the heater box beside the heater motor ,,2 scews hold it in and it looks like a credit card when its out,,,,

Anonymous

  • 1 Answer
  • Posted on Nov 16, 2009

SOURCE: cylinder numbers / engine diagram for 2000 maxima

left_right
2___1
4___3
6___5

left and right banks... the right bank is the bank next to the firewall... cylinders 5 & 6 are next to the tranny.

ZJLimited

ZJ Limited

  • 17989 Answers
  • Posted on Dec 27, 2010

SOURCE: Need the location and firing

1996 Nissan Maxima 3.0 liter DOHC V-6 (VQ30DE)

zjlimited_77.gif


Hope helps (remember to rate and commen this answer).

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Just replaced valve covers on Nissan Maxima 2002 due to misfire. Now it smokes and burns oil every start? What's should I do .

If is is only smoking when you first start it up. Most likely the valve guide seals, oil is leaking into the cylinders and smoking when you start it up.
1helpful
1answer

How do I program a 2004 Nissan Maxima key fob?

Free Nissan Keyless Remote Programming Replacement Key Keyfob Maxima...

2004 Nissan Maxima Key Fob Programming Instructions

2004 Maxima

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again.
  1. Close and lock all doors with the driver's side power lock/unlock switch.
  2. Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast, system will not enter programming mode.
  3. Insert key into the ignition cylinder and turn to the ACC position.
  4. Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press the button more than one time in the above step. If the button is pressed more than one time, the programming procedure will not be successful.
  5. If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver's side power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should flash. Repeat this step for each transmitter (including any existing transmitters).
  6. Turn the key to the OFF position, remove keys from the ignition,
    unlock doors using the driver's side power lock/unlock switch and open the driver side door.

1helpful
1answer

2000 Nissan mis firing,, code reader shows codes: 0430; 0305; and 1320. Assuming its bank 2 cat convertor. Is this where i should start???

430 is Oxygen sensor

0305 is misfire on cylinder 5

1320 is ignition coil.

The ignition coil is causing the misfire. That is causing rich mixture which could case the oxygen sensor issue. You need to work from the ignition issue to the sensor. The reason is if you replace the cat and the engine is running rich it will heat the cat up to the point that the car might catch fire. Oxygen sensors are also prone to fail after about 60 thousand miles.
0helpful
1answer

I have a 2006 Nissan Maxima and my steering wheel is locked and my key will not turn in the ignition

It sounds like your ignition lock cylinder has gone bad on you and needs to be replaced. Hopefully this answers your question. If you have any other questions please feel free to ask.
0helpful
1answer

Nissan maxima keyless entry problem. vehicle will

sounds to me like you need a new ignition switch. not the ignition in which you put the key into but the switch that is mounted to the back of the ignition switch. there is a white round switch mounted to the back of the ignition cylinder. I thing it has a problem. so you don't need the while ignition cylinder, but the electrical portion of it only.
0helpful
2answers

The ignition locks up and i cant turn the key to start the car

the lock tumbler pins may be sticking, buy some powdered Graphite lock cylinder lube from a hardware store, use only this special dry lube, any other type of oil based lube will ruin the ignition lock, spray the powdered graphite into the lock cylinder and insert the key and try to work the lock, do this several times and spray the powder in at least twice, if this doesn't free up the lock cylinder then you will need to have the ignition lock cylinder replaced.
1helpful
2answers

My mechanics say the brain box locked on security. it has refused to start, they've tried all they can but it just wont start, they say the brain box has to be reprogrammed. it a nissan maxima 2000 model....

IF YOU GOT 2 SETS OF KEYS TRY ANOTHER IGNITION KEY.THAT NOT WORN.TURN ON IGNITION FOR 5 SECONDS.SWITCH THE IGNITION OFF.WAIT APPROXIMATELY 5 SECONDS.SWITCH IGNITION ON FOR APPROXIMATELY 5 SECONDS.SWITCH IGNITION OFF.WAIT APPROXIMATELY 5 SECONDS.START ENGINE.IF STARTS OTHER KEY WAS WORN.IF CAR STILL DONT CRANK.THE DEALERSHIP HAS REPLACE KEYS AND ANTI THEFT SYSTEM AND REPROGRAM TO CRANK.ALSO CHECK TO MAKE SURE THE NEUTRAL START BACK UP LIGHT SWITCH IS WORKING.IF FAULTY IT WILL ALSO CAUSE NO START PROBLEMS.
0helpful
1answer

My key will not turn to start my car, what can i

if your steering wheel is not locked your ignition lock cylinder may be seized up-first try moving the steering wheel all the way one direction and turn the key-if this does not work then it may need towed somewhere to replace the lock cylinder
0helpful
1answer

My 98 max wont start sometimes you turn the ignition nothing happens, eventually it sarts, sometimes immediately, sometimes 10-15 mins later it starts

sounds like ignition cylinder has gone bad, try sliding key in and out while turn key and if key slops around cylinder is bad
1helpful
2answers

2000 nisan maxima misfire in cylinder 2

check plug wire coil if that dosent do it pressure test cylinder make sure its ok. if pressure goes down bad cylinder or piston or it could be the head. i hope this was usefull. write me back let me know how it went
Not finding what you are looking for?

169 views

Ask a Question

Usually answered in minutes!

Top Nissan Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...