Question about Hyundai i10

Open Question

Valve clearance Hyundai i10 4 cil. 1.1 l

Looking for the specifications engine 1.1 l valve adjustment clearance

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
starlet4life
  • 89 Answers

SOURCE: Adjust valve clearances 1987 toyota corolla

Im assuming its an 4AGE!?
http://www.ae92gts.com/ae92gts_valve_adj.html
And here one of my favorites...;)
http://www.billzilla.org/4agstock.htm

Posted on Oct 07, 2008

Ad
  • 1 Answer

SOURCE: Valve tappet adjustment

well, I can see ur message has been here for quite some time. Most probably you got the answer to ur request.
I just did the valve clearance on the engine of my SJ413 that has the 1000cc engine of an SJ410 :
When cold: 0.13mm Intake and 0.18mm Exhaust
Engine sounded well and worked fine after that.
Enjoy
Mehdi

Posted on Feb 07, 2009

  • 73 Answers

SOURCE: valve adjustment

tiburon uses hydrolic lash adjusters there are no valve lash adjusting If you hearing a pecking sound on the top of the mtr try some oil additive or replace the hydrolic lash adjusters

Posted on Jun 15, 2009

johnjohn2
  • 5763 Answers

SOURCE: Valve Clearance

valve clearance, with engine hot, intake valves are .005-.006 in, exhaust valves are .011 in, if engine is cold then its intake .009-.011 in and exhaust is .007. hope this helps good luck.

Posted on Nov 28, 2009

michigan man
  • 3533 Answers

SOURCE: valve clearance of 12 valve engine

i do not know but give these websites a try www.alldatadiy.com and www.autozone.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your car wish you the best of luck Michigan Man.

Posted on Feb 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Valve clearance on suzuki vitara 1999 1.6


  • Set the engine to Top Dead Centre (TDC) of the compression stroke for the cylinder to be adjusted.
  • Check the valve clearance. The valve clearance specifications are as follows:

    Intake valves: 0.005-0.007 inches (0.13-0.17mm) Exhaust valves: 0.005-0.007 inches (0.13-0.17mm)
  • After adjustment, tighten the lock nuts to 11-14 ft. lbs. (15-19 Nm).
  • Repeat for each valve to be adjusted.
  • Feb 16, 2017 | Suzuki Cars & Trucks

    1 Answer

    What is the clearance between the rocker arm and the valve spring in a GM 2.2L motor


    there is no specification for what you want
    the valve clearance is between the end of the rocker arm and the end if the valve stem
    the stem end is proud of the spring retainer so if your rocker arm is touching the spring retainer , you have a big problem as for the procedure it is set out in the workshop manual but if you don't have a manual it can be done like this
    you will need the firing order of the engine first
    now adjust no 1 piston valves when the next piston to fire has the valves in the rock position
    that is the exhaust valve just closing as the inlet is just opening a bit of movement of the crank makes either valve move up or down
    adjust no 1 piston valves
    now move on to the next piston to fire and adjust the valves that were rocking
    follow that procedure until all the valves are adjusted
    for example
    on a 4 cylinder engine with a firing order of 1--3--4--2
    bring up no 1 piston and adjust the valves when the valves on no 3 piston are rocking
    next piston to fire is no 4 so adjust no 2 piston valves
    next piston to fire is no 2 so adjust the valves when no 1 valves are rocking
    the procedure is the same for engines with any number of cylinders

    Oct 19, 2016 | Cars & Trucks

    1 Answer

    How do I adjust valve clearance on 912/3 deutz engine


    firing order is 1-2-3
    so when no 2 cylinder valves are in the rock position ( exhaust closing at the same time as inlet is opening) that will be no 1 piston tdc compression stroke adjust the both valves to the specification
    .006" both valves
    when no3 piston has valve rock adjust no 2 cylinder valves
    when no 1 has valve rock adjust no 3 cylinder valves
    go google and type in valve clearance of deutz 3 cylinder engine
    there is another method explained where inlet of one cylinder and exhaust
    this is done with one full revolution of the crank
    www.deutzamericas.com page 42 of the manual

    Oct 16, 2016 | Cars & Trucks

    1 Answer

    What are the valve lash specs for 2007 Honda Accord V6?


    There is a specific procedure for setting valve clearance . I highly recommend getting a repair manual for the correct specs & procedure. The engine must be at TDC with the #1 cylinder on the compression stroke , that will allow you to adjust ONLY certain valves , then you have to turn the engine one turn to TDC again only now #1 will be on the exhaust stroke & the rest of the valves can be adjusted . it's important that you know the difference between the two !

    Jan 08, 2015 | Honda Cars & Trucks

    1 Answer

    Valve Clearances inlet and exhaust


    j24b engine D.O.H.C.
    U.S.A?
    open hood , look up. see white sticker, see clearances.?
    off online F.S.M
    Valve clearance specification when cold :
    59 to 77deg F or 15 to 25deg C (engine temps)
    Intake: 0.0063 to 0.0094 inch (0.16 to 0.24mm)
    Exhaust: 0.0123to 0.0153 inch (0.31to 0.39mm)
    you must remove the bucket,tappet , to change lash.
    MIKE IT (that means a micrometer)
    then buy shims or new buckets to fit. (generic answer)
    the book says buy correct tappet after measuring, yours.
    and it's out of range, and doing the math first.

    that is it.

    May 05, 2013 | 2010 Suzuki Kizashi

    1 Answer

    I need the required valve & inyector clearance on a M11 engine


    Cummins M11

    Intake valve clearance 0.010 inch
    Exhaust valve clearance 0.024 inch

    The firing order is 1-5-3-6-2-4 and that is the order the valves should be adjusted started with first timing mark on main pulley adjust cylinder number 1 The valves and injector should be adjusted at the same time The crankshaft is then rotated 120 degrees to next timing mark and cylinder 5 is adjusted, the crank is rotated again 120 degrees to next timing mark and cylinder 3 is adjusted.then back to the first timing mark, cylinder 6 is adjusted, etc/

    Adjusting nut on plunger should be adjusted to the point where you feel the plunger just reaches the bottom.of travel/bottoms out.

    Feb 15, 2012 | Cars & Trucks

    1 Answer

    There is a tapping noise in the motor but its not knocking I think its a lifter it hasent lost any power and its really not getting worse I would like to know what the spec is for tighing down the lifter...


    Depends on which engine you have. If you have


    ADJUSTMENT Although it is sometimes possible to reuse an old cylinder head cover gasket, in most cases it makes more sense to purchase a new one before beginning the procedure. Some vehicles may require the use of silicone sealant either with or without a new cover gasket. For more details, please refer to the cylinder head cover procedures in Engine & Engine Overhaul of this repair guide and refer to the gasket manufacturer's instructions.

    Z24i Engine
    See Figures 1, 2 and 3
    For the intake valves: 1-4-5-8 valve clearance is 0.012 in. (0.30mm). For the exhaust valves: 2-3-6-7 valve clearance is 0.012 in. (0.30mm). The pivot locknut torque specification is 12-16 ft. lbs. (16-22 Nm).

    1. The valves must be adjusted with the engine warm, so start the truck and run the engine until the needle on the temperature gauge reaches the middle setting. After the engine is warm, shut it off.
    2. Note the location of any wires and hoses which may interfere with cylinder head cover removal, disconnect them and move them to one side. Remove the bolts holding the cylinder head cover in place and remove the cover. Remember, the engine will be hot, so be careful!

    fb38656.gif


    Fig. Fig. 1: Check the valve clearance with a flat feeler gauge-Z24i engine





    e459ab8.gif

    Fig. Fig. 2: Loosen the locknut and turn the adjusting screw to adjust the valve clearance-Z24i engine


    1c1d35c.gif


    Fig. Fig. 3: With the No. 1 piston at TDC, adjust the top set of valves FIRST; with the No. 4 piston at TDC, adjust the bottom set of valves SECOND-Z24i engine

    1. Rotate the crankshaft until the timing marks indicate that the No. 1 piston is at TDC of the compression stroke. If you're not sure of which stroke you're on, remove the No. 1 spark plug and hold your thumb over the hole. Pressure will be felt as the piston starts up on the compression stroke.
    2. Refer to the accompanying illustration (upper part), then check valves (1), (2), (4) and (6) using a flat bladed feeler gauge. The feeler gauge should pass between the valve stem end and the rocker arm screw with a very slight drag. Insert the feeler gauge straight, not at an angle.
    3. If the clearance is not within the specified value, loosen the rocker arm lock nut and turn the rocker arm screw to obtain the proper clearance. After correct clearance is obtained, tighten the locknut.
    4. Rotate the crankshaft until the timing marks indicate that the No. 4 piston is at TDC of the compression stroke. If you're not sure of which stroke you're on, remove the No. 4 spark plug and hold your thumb over the hole. Pressure will be felt as the piston starts up on the compression stroke.
    5. See the illustration (lower part), then check valves (3), (5), (7) and (8). Check and adjust valve clearance as necessary.
    6. Install the cylinder head cover gasket, the cover itself and any wires or hoses which were removed. Check the engine oil level.

    KA24E, VG30i and VG30E Engines
    See Figures 4 and 5
    These models utilize hydraulic valve lifters. Periodic adjustment is neither necessary or possible. There is however a bleed down procedure that is necessary when the valve train has been disassembled.
    HYDRAULIC LIFTER BLEED DOWN
    1. Remove the cylinder head cover.
    2. Check the lifters for proper operation by pushing hard on each lifter with fingertip pressure.
    3. If the valve lifter moves more than 0.04 in. (1mm), air may be inside it. Make sure the rocker arm is not on the cam lobe when making this check.
    4. Install the cylinder head cover.
    5. If there was air in the lifters, bleed the air by running the engine at 1000 rpm for 10 minutes.


    4df22a2.gif


    Fig. Fig. 4: Cross-sectional view of an installed hydraulic valve lifter-4 cylinder engine


    6e01bb3.gif


    Fig. Fig. 5: Cross-sectional view of an installed hydraulic valve lifter-6 cylinder engine

    Oct 29, 2010 | 1989 Nissan Hardbody King

    2 Answers

    Overhead valves making noise like they need ajusting


    Valve Lash ADJUSTMENT 1.6L Engines NOTE: Measure valve clearance with the engine cold.
    1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
    2. Remove the valve cover.
    3. Set the engine to Top Dead Center (TDC) of the compression stroke for the cylinder to be adjusted.
    4. Check the valve clearance. The valve clearance specifications are as follows:
      • Intake valves: 0.005-0.007 inches (0.13-0.17mm)
      • Exhaust valves: 0.005-0.007 inches (0.13-0.17mm)
    5. After adjustment, tighten the locknuts to 11-14 ft. lbs. (15-19 Nm).
    6. Repeat for each valve to be adjusted.
    1.8L, 2.0L and 2.5L Engines The 1.8L, 2.0L and 2.5L engines utilize automatic hydraulic lash adjusters to maintain proper valve lash at all times. Periodic valve lash inspection and adjustment is not necessary or possible. prev.gif next.gif

    Sep 14, 2010 | 2000 Chevrolet Tracker

    2 Answers

    Procedure of tappet adjustment


    make sure engine is warmed up. Put cylinder one at top dead center,remove the valve cover,loosen all adjustment lock nuts,adust intake and exhaust valves on cyl #1 and intake valve on #2 and exhaust valve on #3. now rotate crankshaft 360 degrees clockwise, now adjust intake valves on cyl#3 and cyl #4 and exhaust valves on cyl #2 and cyl #4.now tighten lock nuts and install valve cover. specs are intake valves 25mm clearance and exhaust 28mm clearance, use a feeler gauge,heres a picture to show you where to check clearance.7675a52.gif

    Mar 14, 2010 | 1986 Suzuki Samurai

    1 Answer

    Want to know what the valve clearances are for my 1999 hyndai excel


    Adjust the jet valve clearance before the adjustment of the
    intake valve clearance.
    Jet valve clearance (hot engine)
    [Standard value]. . . . . . . . . . . . . . . . . . . 0.25 mm (0.010 in.)

    now adjust valve clearance
    Valve clearance (hot engine) [Standard value]
    Intake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.15 mm (0.006 in.)
    Exhaust. . . . . . . . . . . . . . . . . . . . . . . . . . 0.25 mm (0.010 in.)

    Jul 30, 2009 | 1990 Hyundai Excel

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    283 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hyundai Experts

    yadayada
    yadayada

    Level 3 Expert

    76164 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8273 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...