Question about Mitsubishi Cars & Trucks

Open Question

Location of crank angle sensor on 94 pajero

Want to replace part don`t know where it is in the engine

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: audi a4 2.8 30v 1998 ack engine

It is mounted to the transmission bellhousing on the driver's side. The connector is mounted on the firewall and is a smaller, gray connector. You can reach the sensor from underneath.

Posted on Apr 01, 2009

  • 701 Answers

SOURCE: need location of crank angle sensor on 1997 pontiac sunfire 2.2 liter

Hello oldiro: My name is Roger and I can help. From under the vehicle look up between the transmission and the side of the block. Mid motor above the pan rail there is a bolted in sensor. This should be the crank sensor.It will have two wires plugged in to it. Please rate this answer as this lets us know you received the information you asked for. Should you need further help please just ask. Thank You for using FixYa. Roger

Posted on May 06, 2009

localwonder
  • 6784 Answers

SOURCE: crank angle sensor location

The crank sensor is always located next to the crankshaft pulley. it will be inserted into the block with the top part of the housing half way out. you cant miss the wires leading into the tip of the housing next to the crank shaft pulley.

Posted on May 23, 2009

kidspeedy
  • 321 Answers

SOURCE: knock sensor 1996 v6 3.3 nissan pathfinder

The Crankshaft Position Sensor is located: Under hood, driver side, front engine area, mounted rear of crankshaft pulley
The Knock Sensor is located: Under hood, center, front engine area, below intake manifold, mounted on block

Posted on Jun 14, 2009

brandyspoile
  • 61 Answers

SOURCE: Crank Sensor in 94 Isuzu Rodeo

it's on the bottom of the motor, towards the back on the passenger side. It has a small clip of wires and one screw holding it on. You may want to pull it up on ramps- if it'll run- otherwise, get under the Rodeo, it's up a little higher than the oil pan, and to the passenger side. (it's right on top of the two lines that run to the bottom of the radiator.) You will need a 10mm socket to remove it. I have added a few pics showing the location (i just completed this task myself)
bfcf016.jpg61ae995.jpgdeffbd6.jpgdd2e415.jpg

Posted on Jul 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

New engine in 96 Geo Prizm now not firing


Don:
1.6L or 1.8liter engine? Toy 4A or 7A engine?
all 4 cylinder dead. and coil? no spark?
did you hook up all sensors. as the 96 had,(usa car has more)
usa car is OBD2 and runs crank and cam sensors to do misfire detection.(fed law)
any scan tool will tell you why,!
here posted 100 times in ORDER
  1. fuses all good, 12vdc both sides, key on, or its bad.
  2. keyon
  3. CEL lamp in dash turns on, if not ,see #1
  4. plug in scan tool, get comms.? good, pcm talks !
  5. crank for 5 seconds. (least) release key, not off.
  6. SEE Those DTC errors, for spark , cmp,ckp, (P03xx errors)
  7. bingo.? RPM dead cranking? scan tools can see RPM.
  8. sure! my bet by now you found it.

Mar 04, 2015 | 1996 Geo Prizm

3 Answers

I have a 1985 fiero se v6 that was running fine but cutting off after warm up


Do you know what you are loosing when the engine stops running ?

Jan 16, 2014 | 1985 Pontiac Fiero

1 Answer

Does a mitsi pajero E-V25W with a 6G74GDI engine use a crank position or crank angle sensor


Check with a service department but I am sure that it will have.

Oct 23, 2013 | Cars & Trucks

1 Answer

Coil pack not working


It could be your crank angle sensor

Jul 13, 2013 | Audi 100 Cars & Trucks

1 Answer

Location of cam and crank angle sensor in 96 N15


The cam and crank position sensor can be found in the front of the crank on the engine block below or next to the water pump in many applications.
It can also be located on the main crank pully or the flywheel.

Feb 09, 2012 | Nissan Pulsar Cars & Trucks

1 Answer

How do i replace the crank position sensor on a 2000 jeep grand cherokee


If you have the type of crank angle sensor shown in the image, then it will be located on the bell-housing towards the top of the bell-housing and usually on the drivers side. Dis-connect the faulty crank angle sensor and then un-bolt the two bolts that secure the crank angle sensor to the bell-housing and then remove the sensor. The best access to the crank angle sensor is from under the vehicle.


47ada7e.jpg

Jun 21, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Location of crank sensor on 94 Nissan Pickup 4cyc


It is located in the distributer. The part is not sold seporate from the distributer. It is only a dealer item the whole distributer for 450.00$. It is also called the crank angle sensor. Just because the code 0335 comes on on the scan does not mean that the sensor is bad. The best thing to do it take it to a dealer.
Actually the one in the distributor is called a camshaft position sensor. You can by rebuilt distributor for around 250.00. The crank shaft position sensor is located on the Transmission housing on the left side.

Nov 17, 2009 | 1994 Nissan Pickup

1 Answer

Need location of crank angle sensor on 1997 pontiac sunfire 2.2 liter


Hello oldiro: My name is Roger and I can help. From under the vehicle look up between the transmission and the side of the block. Mid motor above the pan rail there is a bolted in sensor. This should be the crank sensor.It will have two wires plugged in to it. Please rate this answer as this lets us know you received the information you asked for. Should you need further help please just ask. Thank You for using FixYa. Roger

May 06, 2009 | Pontiac Sunfire Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...