Question about GMC Cars & Trucks

1 Answer

I have a 2003 GMC Sierra. The engine has started to kick when ideling or driving. anybody have any ideas?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Expert
  • 129 Answers

It may be a bad spark plug, coil pack or fuel delivery problem.

Posted on Nov 30, 2012

Testimonial: "I will start there. Thank you."

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 116 Answers

SOURCE: 2003 GMC Sierra Knock sensor and oil pressure??

the knock sensors are located below the intake plenum,or,upper intake manifold as some call it, they screw into the lower intake, the front one is sensor 1, the rear is sensor 2. it is wise to change both if you have some miles.since you are going to be buying a gasket set to do this job.the sensors are cheaper than the gaskets.

Posted on Jun 12, 2009

cshubart
  • 146 Answers

SOURCE: My Power window on my 2003 GMC Sierra 1500 Truck

if your main switch panel still works the passenger window and if door locks still work probaly bad window motor

Posted on Oct 21, 2009

Molson02536
  • 3854 Answers

SOURCE: I changed batteries in my 2003 GMC Sierra key fob

1. Close all doors
2. Insert key into ignition
3. Hold down the power UNLOCK button on the driver's door panel, continue to hold down
until instructed to release in step 9.

4. Perform steps 5 through 8 in a fairly rapid succession.
5. Turn the ignition to the ON position (as far as you can go without starting the engine.)
6. Turn the ignition to the OFF position.
7. Turn the ignition to the ON position (as far as you can go without starting the engine.)
8. Turn the ignition to the OFF position.
9. Release the power UNLOCK button on the door panel. The vehicle should respond by
door locks locking and unlocking automatically. (If locks do not cycle after you let go,
not before you let go of the unlock button, then the vehicle has not entered programming
mode and you must start procedure over. Remove key from ignition, open drivers door
and return to step 1 ). If the locks do cycle automatically then proceed to step 10.

10. Hold down the LOCK and UNLOCK buttons on the remote until the doors lock and
unlock. This may take up to 30 seconds.

11. Repeat step 10 NOW for each additional remote. (Including any existing remotes).
12. Turn the ignition to the ON position to exit the programming mode.
13. Test remote(s).

Posted on Mar 06, 2010

  • 1 Answer

SOURCE: wiring diagram 2003 GmC Sierra

I need wiring digram for GMC 2003 SIERRA . I have the left head light working fine but the right I have no power to it. I have checked the fuses and relaysand so far have not found and broken or frayed wires.

Posted on Mar 06, 2010

  • 2926 Answers

SOURCE: My 2003 GMC Sierra Idles Rough And Cut Off

Before replacing the O2 sensors, I would check the fuel pressure. You may also try to have someone pull a trouble code from the powertrain control module to verify why the engine light is on. Do not replace any parts until this is done, otherwise your going to be guessing at the root cause, and it will get expensive with part replacement.

Posted on May 12, 2010

Testimonial: "Trouble code P0101 {Mass Air Flow}and code P0332 Knock Sensor.Thanks i saved a lot money."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2003 GMC SIERRA PU. 5.3 keep getting the " Reduced engine power " code , any Ideas on where I should' start looking?


You should take it to a garage that has a GMC scan tool and scan it for the error code.

Jul 31, 2015 | GMC Cars & Trucks

1 Answer

My 1985 GMC Sierra TH350 trannys. The speedometer isn't working but will ping sometimes. I have no idea what it is so anybody please help


The gear that is in the adapter for the transmission is plastic and they would strip out, easy fix and cheap too

Feb 09, 2013 | Cars & Trucks

1 Answer

My 2003 GMC sierra has a clunk. It happns when I am coasting, say while turning or slowing in traffic then I exelerate about 50 - 75% of the time I get a singe clunk. It seems it occurse most when it is...


Hi, without driving it to experince the noise first hand i would tend to say its the rear diff. Other causes can be a broken engine or transmission mount. Good luck

Aug 27, 2010 | 2003 GMC Sierra 1500

1 Answer

2003 gmc sierra 1500 4 wheel drive truck kicks in to 4 wheel drive on its own while driving down the road


look out the code.. and check the speed sensors and the harness......check also the switch maybe you use the auto 4 wheel...thars why it engage its self automatically depending on the road,

Jun 27, 2010 | 2003 GMC Sierra 2500HD

1 Answer

Excessive black exhaust on 2003 GMC Sierra Duramax Diesel.


This is what i would try (cheapest first) redexe/wyyns
injector cleaner,double dose,then i have put 1gal gas in 10gal diesel to increase burn temp (you may encounter a hot start problem temporarilly)then if still smoking, get a compresion check on the engine(this will tell you volumes)
by the way the NATO tanks put in 1/3 gas in diesel to stop it freezing in arctic conditions.any more than 1/3 can result in problems.

Mar 17, 2010 | 2003 GMC Sierra

1 Answer

I have a 2003 gmc sierra My automatic transmission is not shifting grears when it's on drive but if i shift from frist to second it will do it and then second to third it won't do anything it acts like its...


Sounds like the sprag or the sun gear gave up. The trans will need to come out and be rebuilt. I think amco will check it out for free and give you an estimate?

Oct 27, 2009 | 2003 GMC Sierra 1500

1 Answer

Engine power is low


Fuel filter replacement may solve this,a tune up probably in order.depending on you maintenance history.Some people do preventative maint. others fix what breaks.Good luck!

Jan 23, 2009 | 2003 GMC Sierra 1500

3 Answers

4X4 inop on 2003 GMC Sierra 2500HD


I have found that when you are going to engauge 4x4 high, it is best to only be going about 3 miles an hour. Not faster, not stopped. It likes some movement to help it mesh. I've had perfect shifts since I started this. Hope it helps. Wade.

Jan 09, 2009 | 2003 GMC Sierra 2500HD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...