20 Most Recent 2009 Mercury Mariner V6 Questions & Answers

Where is my key factory code on mercury mariner 2005

http://www.fixya.com/cars/t26654679-coolant_temp_sensor_2011_mercury This should help you locate where it is.

https://www.wikihow.com/Disable-a-Seat-Belt-Alarm There is a question that in some states it may be ******* and you could be liable in a law suit.

Depends on which ones. If you can get to them you just unscrew the sensor from the exhaust.

Throttle body may be stuck. Spray come cleaner into it. Also a large vacuum leak will cause a high idle.

Hello...In order to isolate the problem the "wrench Light" is indicating a fault code has been stored in the vehicles computer. The first step to determine what the problem may be is to retrieve the code(s) via a ODBII code reader. Some parts stores offer free code reading so check with your local Auto Parts retailers for this service.

Chec fluid level in 4wheel diff n brake resevoir. Partstore can help u. Cud alsi b a module issue. Git it scand while ur there

See this link: Custom Marine Services Quick Source Installation Help Marine Battery Chg... Custom Marine Services Quick Source Installation Help Marine Battery Chg... Custom Marine Services Quick Source Installation Help Marine Battery Chg...

No. Flasher does not control brake lights. Brake lights are controlled by brake pedal switch. Are the emergency lights working?

Doesn't have a CJB , has SJB - smart junction box . Computer with fuse box in one . Removal NOTE: Prior to removal of the SJB, it is necessary to upload module configuration information to a scan tool. NOTE: The tire pressure monitoring system (TPMS) functionality is integral to the SJB. NOTE: A new SJB module is delivered in manufacturing mode with pre-set DTCs. These DTCs require that the TPMS sensor training procedure be carried out in order for the DTCs to be cleared. The pre-set DTCs are as follows:

• B2868 - Left Front Tire Pressure Sensor Fault
• B2869 - Right Front Tire Pressure Sensor Fault
• B2870 - Right Rear Tire Pressure Sensor Fault
• B2871 - Left Rear Tire Pressure Sensor Fault
• C2780 - ECU in Manufacturer Sub-State

1. Upload the module configuration information from the SJB. For additional information, refer to Section 418-01 .

1. Disconnect the battery. For additional information, refer to Section 414-01 .

1. Remove the floor console SJB cover.

1. Remove the transmission selector lever bezel from the floor console finish panel.

1. Apply the parking brake.

1. Remove the parking brake lever boot from the floor console finish panel.

1. Remove the floor console finish panel.

1. Remove the SJB screw.

1. Disconnect the electrical connectors and remove the SJB.

It should be either plugged into the fuse box, or hanging from a wire loom right at the fuse box.

Could be faulty pump in tranny, did you check pump when you pulled transmission ?.

Taking it to a qualified repair shop would be your best bet . U2023 External Node Fault DTC ABS Module REFER to Section 418-00 . U2023 Fault Received From External Node SJB REFER to Section 418-00 . Which module did you pull this code from ? What type scanner or was it a code reader ? Do you know what a serial data network is ? specifically C.A.N - controller area network ! Do you know what a node is ? A control module ,PCM ,SJB ,IPC etc... Communications Network Smart Junction Box (SJB) The SJB is connected to the medium speed controller area network (CAN) communications bus. If one of the bus wires becomes shorted to ground or voltage, communications can continue at a reduced level. Check circuits 1847 (WH/OG), and 1848 (PK/OG) between the SJB C2280a, the instrument cluster C220 and the data link connector (DLC) C251. Total resistance values must not be more than 5 ohms. If the resistance is more than 5 ohms, there is an open circuit in the medium speed CAN, damage to the DLC C251, or damage to the SJB C2280a. Since both the SJB and the instrument cluster share network termination responsibilities, a problem in either of these modules can result in a medium speed CAN failure. For additional SJB information, refer to Section 419-10 . Powertrain Control Module (PCM) The PCM is on the high speed CAN. The PCM controls the engine for better fuel economy, emissions control, failure mode detection and storage, and all passive anti-theft system (PATS) functions. If one of the bus wires becomes shorted to ground or voltage, communications can continue at a reduced level. Check the high speed CAN circuits 1908 (WH) and 1909 (BK), between the PCM C175b and the DLC C251. Total resistance values must not be more than 5 ohms. If the resistance is more than 5 ohms, there is an open circuit in the high speed CAN, damage to the DLC C251, damage to the PCM C175b, or a problem in the in-line connector. Since both the PCM and the instrument cluster share network termination responsibilities, a problem in either of these modules can result in a high speed CAN failure. For additional PATS information, refer to Section 419-01B . For additional PCM information, refer to the Powertrain Control/Emissions Diagnosis (PC/ED) manual. For removal and installation information, refer to Section 303-14A or Section 303-14B . Instrument Cluster The instrument cluster is on the high speed CAN. It is an analog face cluster with a digital odometer. The instrument cluster displays a variety of information. If one of the bus wires becomes shorted to ground or voltage, communications can continue at a reduced level. Check the high speed CAN circuits 1908 (WH) and 1909 (BK) between the instrument cluster C220 and the DLC C251. Total resistance values must not be more than 5 ohms. If the resistance is more than 5 ohms, there is an open circuit in the CAN network, damage to the DLC C251, damage to the instrument cluster C220, or a problem in the in-line connector. Since both the PCM and the instrument cluster share network termination responsibilities, a problem in either of these modules can result in a high speed CAN failure. For additional instrument cluster information, refer to Section 413-01 . The vehicle has 3 module communication networks: high speed and medium speed CAN network, which are comprised of unshielded twisted pair cable, and the international standards organization (ISO) 9141 communication network, which is a single wire network. All 3 networks are connected to the data link connector (DLC). This makes diagnosis and testing of these systems easier by allowing a diagnostic tester to be able to diagnose and control any module on the 3 networks from the connector. The DLC can be found under the instrument panel between the steering column and the radio.

cracked fuel line at the tank, over flow when filling leaking fuel sender unit ( if fitted) rust hole in the tank

There is a black rubber flex boot between the body an the door ,power and ground wire's for the switch run through it . Opening an closing the door over time can cause the wires to break . Pulling the door inside trim panel to get to the switch wiring connector to test for B+ voltage an ground is the way to test electrical . Looking at a wiring diagram to see what wire is what should be done also. Do power lock's work ? Window Operation The window system operates under the control of the accessory delay relay. The smart junction box (SJB) will ground the coil side of the accessory delay relay when the ignition switch is in the ON position. When the accessory delay relay is active, power is supplied to each window control switch. The window control switches direct power and ground to the appropriate power window motor. If the other windows work ,it's not a fuse problem . Broken wire's ,master switch !

Fix your car right away, by clicking the link Mercury Mariner 2005 2007 Factory Service SHop repair manual download

You don't, have to fix the system

Should just unhook battery cable for 15 minutes and hook it back up. The PCM then has to relearn your driving habits,but just drive normally. don-ohio (:^)

Usually the traction control system.If the light is on the system is turned off due to a problem that needs to be repaired.Info should be in your owners manual.