Dehumidifiers - Page 3 - Recent Questions, Troubleshooting & Support

I have one that did the same thing. I had to raise it about 1-2 feet to get it to drain properly.

It sounds like your dehumidifier is likely experiencing an issue with the condenser. If the container was half filled, then it's possible that the condenser has become clogged due to a buildup of sediment or debris. To fix this, you should unplug the unit and remove the cover to check for any blockages. If there are any, then you can use a vacuum cleaner or compressed air to remove them. Additionally, you should also inspect the condenser for any signs of wear or damage. If the condenser is cracked or damaged, then it will need to be replaced. If you need further assistance, you can consult a professional technician for diagnosis and repair.

https://www.searspartsdirect.com/manual/44av6atl6i-003204/lg-ldf7551st-dishwasher-parts?sid=sem:ggl:dsagroupb:141452280898::c&keyword=&gclid=Cj0KCQiAtICdBhCLARIsALUBFcHCsKc_OEAYHAPPbyS-9LcLCYIAojCvzFzeIbtp7dOcMwOBVditVK8aAhxCEALw_wcB

This problem is usually caused by an improperly installed water collection bucket or the float valve inside the top of the bucket is broken or stuck in the DOWN position.

To troubleshoot this, turn the unit OFF & unplug it. Remove he bucket, check the float valve's position. If it stuck in the UP position, jiggle the handle to make it return to the DOWN position. This will also allow you to determine if the float is broken. If all this checks out, reinstall the bucket "squarely" from top to bottom into the bucket holder. It must make contact with the bucket safety removal switch on the back wall of the holder. When installed properly, the bottom of the bucket will not tilt down at all. Plug the unit in and turn it ON. If everything was done correctly, the unit should start within a few seconds.

Hope this helps you to troubleshoot and solve the problem. Thnanks for choosing FixYa.

What does the user manual say about this?

Question moved from motorcycles category No there are no parts and nothing that will fit. What it wrong with the old tank that can't be fixed with Epoxy Putty or Epoxy Resin? https://www.google.com/search?q=Kenmore+humidifier+17006%2C+tank ..

You need a new humidistat. There are two here, but not sure if you your machine https://www.fix.com/parts/heating-and-cooling/dehumidifier/whirlpool/ There are numerous listings on Amazon, but all unavailable. https://www.amazon.ca/Kenmore-Whirlpool-WP1168670-Dehumidifier-Humidistat/dp/B077B1VZSV ..

My unit runs for a half hour and then theme dreaded E9 comes up. Then the fan runs but no buzzing from the condenser. Sounds like everyone who buys this brand has this problem !! I will try the manic press and hold the start button and hope it works.

Appliances like this have a motor that can run both ways and is push by the alternating cycles in the power supply. Sometimes you can retrain it by wearing heavy gloves and spinning it the right way as you turn it on. Leave it running for five minutes, switch off and back on before the fan stops. You can also contact Broan Nutone direct. https://www.google.com/search?q=broan+pm390-hs+blowing ..

i don't know. it is common for dehumidifiers to not collect water in cold weather. please consider obtaining a portable device that shows how humid the air is where your machine is located. i find 55 or 60 is suitable for my basement.

I have the same issue, all 4 wires have voltage for my connector, I would assume one would be ground but it seems that is not the case unless that is the issue. Black wire I would assume would be ground but it isnt. If anyone has a wiring diagram for these units I could figure it out but I can only go so far when you are operating in the dark.

dont know anything about a wheel chair lift, but why is it posted in dehumidifiers repair section?

For the slightly larger model, FFAD7033R1, F1 turned out to be the humidity sensor. This can be accessed by removing just the back panel.If you have a soldering iron for less than a nickel you can just replace the NTC Thermistor (small orange resistor 10k) on the small PCB. See attached image below.In the image below just to the right of the white sensor you can see I removed the bad thermistor..

Hello there,
Your guess is right as to what the cause of the problem is. The relative humidity (RH) sensor is faulty and need to be replaced. That is why it is stuck on 30%. When the RH is faulty, the compressor will not run. And the dehumidifier will not do anything.
Hope the moisture collected in the bucket is removed, becuse that also could be a cause of the problem. If the bucket that collects moisture is full, the sensor will send a message to the compressor and have it shut down automatically till the bucket is empty.
Once it is confirmed that the moisture collecting bucket is empty and it is still not reading anything other than 30%, then that confirms the problem to be from the RH sensor.
Hope this helped. All the best. Elect_Comp

Danby's Consumer Help Line (1-800-263-2629) is always busy. So, I called their General number: 419-425-8627. The receptionist transferred my call to their Service dept. My call was answered in 2 minutes.

The Service Rep. described the following code for my dehumidifier model (DDR657EE):
P1 = Defrosting: the unit will go into Defrost mode periodically to ensure that the parts are working at the right operating temperature. It should be in Defrost (P1) mode for only a brief period of time. If the unit is in Defrost (P1) mode continuously for a couple of hours (or more), then you should call Danby Service for further assistance.

He had no documentation of a P2 code for my model.

He also described other General Codes (applicable to most Dehumidifier/Humidifier models):
E1 = Not enough water
E2 = Not draining
E3 = Water temperature too cool
E4 = Overflow Switch activated
E6 / E7 = Problem with Temperature Sensor

I hope that helps.

'make and model' are needed in all questions please. However it appears to be Noma or Hisense. See videos and articles. https://www.google.com/search?q=Dehumidifiers+error+E9 ..