I have connected Lantronix UDS1100 Device with Siemens AZL Meters. But not able to get complete data on front end.

It goes normally from the back right through to the front and is connected there

CLEAN REGISTRY - This resets the device to factory settings, losing applications but keeps your data intact.
FACTORY DEFAULTS - This completely wipes everything and resets the device back to it's factory defaults.
SKIP
Try Clean Registry first.

Please see the link here below for the complete manual.
http://www.lantronix.com/pdf/UDS1100_UG.pdf

If you go to page 70 you will see the complete pin layout for RS232, if you need to connect it to a PC with a 9 pin RS232 port you can see the equivalent on page 72.

Please let me know if you need more details.

I would look for new WiFi stuff and other wireless equipment in the vicinity as someone else may have a system that is interfering with your system.

To reset the SCS to factory so you can assign a new IP, use a paper clip to depress the button inside the reset hole. Hold that button and recycle the power, continue to hold the button after power cycle for 15 seconds.

Hi,

Are you asking about a serial cable to connect the serial port on the MSS100 to (for instance) a Com port on a PC?

If that's the case you can use a DB9-to-DB25 null modem cable. Here's an example: http://www.cablestogo.com/product.asp?cat_id=936&sku=03019

You will also need a DB25F/F gender changer in order to use this cable.

If the MSS100 already has an IP address that is valid on your network you can telnet to it or open it's web configuration manager in a browser to configure it.

There are video tutorials of various ways to assign an IP address to an MSS here: http://ltxfaq.custhelp.com/cgi-bin/ltxfaq.cfg/php/enduser/std_adp.php?p_faqid=1114

There is also a FAQ: http://ltxfaq.custhelp.com/cgi-bin/ltxfaq.cfg/php/enduser/std_adp.php?p_faqid=167

Installation and configuration information is in the Installation and Getting Started chapters of the MSS User Guide, http://www.lantronix.com/pdf/MSS_UG.pdf

If you have further questions, please give Lantronix Technical Support a call at 800-422-7044, or post a question here: http://ltxfaq.custhelp.com/cgi-bin/ltxfaq.cfg/php/enduser/ask.php

Regards,

Gary Fisher
LANTRONIX
Senior Technical Support Engineer
167 Technology Drive, Irvine, CA 92618
Phone: (800) 422-7044 or (949) 453-3990

Post Technical Support questions at http://ltxfaq.custhelp.com/cgi-bin/ltxfaq.cfg/php/enduser/ask.php

Get real-time help online! Use Live Assist at http://www.lantronix.com/support/live-assist.html

its due to motherboard problem.
install ur chipset driver

To do a Hard Factory Reset:
Simultaneously press the Suspend/Resume (END) button whilst pressing the stylus tip into the reset opening.
Keep them held until the screen comes back on. Then release the buttons
You will get the Boot options:

CLEAN REGISTRY - This resets the device to factory settings, losing applications but keeps the data intact.

FACTORY DEFAULTS - This completely wipes everything and resets the device back to it's factory defaults.

SKIP
Try Clean Registry first.

Try the LS100 from www.sena.com, it has a better warranty (5yrs vs 1yr) and its about half the price of a uds-10. We've had the same experience with the four UDS-10's we have and now 3 of the four have stopped working and report the following error: "FATAL ERROR 01/Setup memory: Contact tech support". I called there tech support and the guy (Marty) actully told me that the units have exceeded their life expectency. They all failed within the first ~22 months of operation. Working in a school district we cannot afford to keep doing the same thing over and over and over again, so our next project which involves 15 building will all use the SENA LS100 product and save the district money and have way better support and warranty. Thanks goes to "tech support" person Marty at Lantronix.

I would check your flow control on both the device and on the UDS1100. Also make sure your baud rate, stop bits and parity match