It won't turn

Step 1:

see the diagram attached.

Clean the motor, lube the gear+shaft
Adjust the small POT for a little.
RUN the software calibration for troubleshooting. see the diagram

Step 2:

Step 3:

Step 4:

he Steps for Newer Style Console Calibration
1.Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)
2.Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).
3.Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.
4.If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.
5.Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.
6.Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.
7.Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.
8.Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.
9.Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."
10.Press ENTER. You should see "SS" or "55" in the console.
11.Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.
12.Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.
13.When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.
14.Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.
15.If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.
God bless you

Make sure the VGA cable is properly inserted to your pc and monitor

Hello! Here is your solution.
1. Press Stop/Reset button for 5 seconds. 2. After 5 seconds your printer will start one process. 3. Now release to hold the button.
Now your printer is ready to use.... thanks

I know you don't want to hear this, but either you did something to the hose filter or you didn't get it plugged back in correctly.

If you banged the water inlet valve in moving it back, it might be damaged.

Suggest you unplug everything and start over.

Cause: Head too hot, exceeds the threshold, usually the color Catridge
Solution:

1. Turn Off printer, cable power still plug in.

2. Press Stop/Reset button, don't release the button.

3. Press Power button by holding without release and than release Stop/Reset Button.

4. Press Stop/Reset button two times (2x) now release the Power Button.

5. Wait until service mode to zero (0).

6. Turn off the Printer, cable power still plug in.

7. Press Stop/Reset button, don't release it.

8. Press Power button don't release & than release Stop/Release button.

9. Press Stop/Reset button four times (4x), wait until service mode to "1"

10. Turn off printer, and loose cable power, wait for one (1) minute.

11. Connect cable power, turn on printer again, now this printer ready to use.

To solve your problem follow the instruction step by step...

1. Turn Off printer, cable power still plug in.

2. Press Stop/Reset button, don't release the button.

3. Press Power button by holding without release and than release Stop/Reset Button.

4. Press Stop/Reset button two times (2x) now release the Power Button.

5. Wait until service mode to zero (0).

6. Turn off the Printer, cable power still plug in.

7. Press Stop/Reset button, don't release it.

8. Press Power button don't release & than release Stop/Release button.

9. Press Stop/Reset button four times (4x), wait until service mode to "1"

10. Turn off printer, and loose cable power, wait for one (1) minute.
Connect cable power, turn on printer again, now this printer ready to use

To solve your printer problem using the following directions..

Follow this instruction step by step.

1. Turn Off printer, cable power still plug in.

2. Press Stop/Reset button, don't release the button.

3. Press Power button by holding without release and than release Stop/Reset Button.

4. Press Stop/Reset button two times (2x) now release the Power Button.

5. Wait until service mode to zero (0).

6. Turn off the Printer, cable power still plug in.

7. Press Stop/Reset button, don't release it.

8. Press Power button don't release & than release Stop/Release button.

9. Press Stop/Reset button four times (4x), wait until service mode to "1"

10. Turn off printer, and loose cable power, wait for one (1) minute.

11. Connect cable power, turn on printer again, now this printer ready to use.

1. Turn Off printer, cable power still plug in.

2. Press Stop/Reset button, don't release the button.

3. Press Power button by holding without release and than release Stop/Reset Button.

4. Press Stop/Reset button two times (2x) now release the Power Button.

5. Wait until service mode to zero (0).

6. Turn off the Printer, cable power still plug in.

7. Press Stop/Reset button, don't release it.

8. Press Power button don't release & than release Stop/Release button.

9. Press Stop/Reset button four times (4x), wait until service mode to "1"

10. Turn off printer, and loose cable power, wait for one (1) minute.

11. Connect cable power, turn on printer again, now this printer ready to use.

Follow this instruction step by step.

1. Turn Off printer, cable power still plug in.

2. Press Stop/Reset button, don't release the button.

3. Press Power button by holding without release and than release Stop/Reset Button.

4. Press Stop/Reset button two times (2x) now release the Power Button.

5. Wait until service mode to zero (0).

6. Turn off the Printer, cable power still plug in.

7. Press Stop/Reset button, don't release it.

8. Press Power button don't release & than release Stop/Release button.

9. Press Stop/Reset button four times (4x), wait until service mode to "1"

10. Turn off printer, and loose cable power, wait for one (1) minute.

11. Connect cable power, turn on printer again, now this printer ready to use.

Follow the instructions step by step

1. Turn off printer, cable power still plug in,
2. Press Stop/Reset button don't release
3. Press Power Button don't release and than release Stop/Reset button
4. Press Stop/Reset button 2X , wait until service mode to " 0 "
5. Turn off printer, cable power still plug in
6. Press Stop/Reset button don't release
7. Press Power Button don't release and than release Stop/Reset button
8. Press Stop/Reset button 4X , wait until service mode to " 1 "
9. Turn off printer, and loose cable power, wait one minute.
10. Connect cable power, turn on printer again, now this printer ready to use.