20 Most Recent Ryobi Factory Reconditioned 18" 40cc 2-Cycle Gas Powered Chain Saw #ZRRY10532 - Page 7 Questions & Answers

Just got to same point, alas its a complete stripdown and engine is to be taken out. Retaining bolts for the pump are underslung through the engine casing.

stop using it and have it repaired before the pump is totallly destroyed.

Most good Lawn mower suppliers can get you a new blade. You can also usually get them online. Have you tried contacting Ryobi directly to see if they can send you a replacement. What is wrong with the blade? A lot of mower blades can be re-sharpened to reduce the need to buy a replacement every time it goes blunt.

check switch first then coil. Use a multimeter and set the positive lead of the multimeter in position where the spark plug would usually insert ensure it has made good contact. Place the negative lead onto the metal body of the ignition coil. A working ignition coil will give a reading of between 2.5 - 5 k ohms. Hope this helps.

Test charge port interlock, see attachment.

Ryobi One + is the battery system. One 18 volt battery powers all of the range of tools. Their Service and Support in the link. https://www.ryobitools.com/products/one-plus?ryobitools_production_plp_products%5BrefinementList%5D%5Bpower_detail%5D%5B0%5D=18v ..

Are you in South Africa? It doesn't seem to be a known model in North America where we are. This link might work better for you. https://www.google.com/search?q=Ryobi+JT200+parts and also https://www.google.com/search?q=Ryobi+JT200+belt&rlz=1C1QJDB_enCA643CA644&sxsrf=APq-WBtBERd3qAMszYcAMMHfwL-snySOGQ:1643739137693&source=lnms&tbm=isch&sa=X&ved=2ahUKEwia2J67jd_1AhUplIkEHZH4A1EQ_AUoAnoECAEQBA&biw=1920&bih=937&dpr=1 ..

are these what your looking for,, Item location:Adelaide, SA, Australia $89.00https://www.ebay.com.au/itm/Ryobi-PLANER-BLADES-318mm-2-Pieces-PTB02PK-Double-Edge-High-Speed-Steel-for-Wood/253294680562?epid=1683394364&hash=item3af98a19f2:g:sDsAAOSwz2tZjTTX

Do you see any fuel leaking when you have it tilted? Grommet or gas gasket or hole in a fuel line might be pulling in air and stalling out. I've had 3 different line trimmers and that happened to all of them. Not a Ryobi tho. I thought they made drills lol. Jk

Easy way to determine... identify which tube has the filter and connect only that tube to either carb port. Then press the purge bulb several times. If fuel spurts out the other carb port then its correct and simply attach the other tube.

If no fuel spurt, then likely you will see air bubbles in the tank. Switch the line (with filter) to other carb port and press purge several times. If no fuel spurts then some other problem.

Do not use the fuel return without the filter for this procedure as it risks plugging the carburetor with debris from the tank.

I would check the governor or maybe it is just a spring from the governor to the carb.

Try Ryobi tools or your supplier.

if worn need to replace it

Take it back. If the new one doesn't perform like it should get your money back and buy a Stihl. They will fuel and run the machine before you ever leave the dealer with it to make sure it runs like it should and they can answer any questions and even get you parts. Husqvarna may do the same thing If you need further help, I’m available over the phone at https://www.6ya.com/expert/kelly_69a0cf1b13789df1

I have this machine and it states it requires 4 ounces to 1 gallon gas. This is if you use the i.d.c.oil which is 32:1 it states if other 2 cyc oil is used it requires 6 ounces to 1 gallon fuel. Im trying to add a picture of the machine. I have aryobi 720 sieries. The newer ryobi machines call for the 50:1.

Put a tarp over it

Typical small engine carburetor initial setting is 1.5 turns for both high and low needles. Turn in the idle speed adjust to open the throttle for easier start and run until the low speed air fuel mix is better adjusted. If you treated the fuel with Seafoam do not overdose or guess. Seafoam has a significantly higher specific gravity making it more difficult to draw up for atomization. Better to use untreated fuel until carb adjust is completed.If it runs for awhile with choke then likely the impulse fuel pump is working so the carb gasket orientation is correct but double check the impulse air passage is aligned.It's always a good idea to replace the fuel filter and fuel lines. Be careful to not get the filtered fuel line wrong or any debris in the tank may be drawn into the carb and plug the internal fuel screen. Telltale for a plugged screen is the purge bulb is difficult to depress and rises extremely slow.

I been having the same problem with mines as well and it smokes sometimes when it cuts off

Check YouTube for applicable video.

get the carb serviced. Could be fuel overflow. small engine carbs are very finicky if left sitting for too long with fuel remaining in the carb.