Top 20 British Telecom Synergy 2110 Cordless Phone Questions & Answers

This is a generalist answer not one specific to this phone! One of two problems here, the circuit board still has dirt or water residue on it preventing the signals from the keypad from being interpreted properly (a short), or the keypad its self is not conducting the current from the button pads properly when pressed. Because there are three keys not working then I would imagine its the first problem as the circuits for a keypad circuit is arranged in a grid and this look like the row conductor is not working. Damage like this often occurs to mobile phones months after they get wet as they slowly corrode with the smallest amounts of water left sitting in between or under the chips on the boards. If the phone has had water spilt on it then it isn't usually a problem if dried properly, anything else though usually is more of a problem. The rubber keypad can be removed and washed in warm soapy water. The underside of each button is a conductive rubber and needs to be free of any 'stickyness'. these are usually pretty robust. (Only the rubber bit with the printed numbers on it!) Once cleaned pat dry, even put it somewhere warm dry, or use a hair dryer.. once your happy there is no water left in the buttons etc put it together and try the phone again. I suspect it wont fix your problem though but that's the easiest fix of the two. If you don't want to pay for it to be repaired then have a poke around as its not going to be much use as it is, you'll need to do a bit of investigative work. Take the phone apart, look for a track on the main circuit board that goes to each area where the 789 buttons would sit, follow it from the buttons and eventually it will go to a black chip on the circuit board, somewhere between that chip and the button pads is your problem. Look how clean the circuit board is near that chip, its likely the 789 button track goes to one of the pins of the chip and it is shorting to one of the pins next to it. if you confident use a pin and gently scrap between the pins, check both sides of the board in the same area for anything dirt related. If you can get hold of an air line blow under the chip where the tracks go, (make sure nothing is around that is loose on the board that can blow away) Other than that without a friend with a soldering iron there's not a lot else you can do.

listen to all the messages. clear them one at a time.

Still error ,handset registration fails although keep on trying step 1&2 in my kx-tg2360jxs panasonic cordless phone , what shall i do ? Shall i change handset batteries ? Really i got bored , is their any one facing my problem ? Help me please

The cord or cable connecting the phone to your pstn line is called line cord. check the connection at the back of phone and the wall jack. if it is ok change the cord and check.

I reset my phone but lost numbers and doesnt help with pin. Still cant find a way of overriding old pin.

you need to flash your phone..to enable it work all right

Hello

This problem is from the network provider and not from the phone.

Call your network provider to rectify the problem for you.

Take care.

SCAM

I had the same problem, it was because someone sent me a media message that couldn't be displayed. If you've gotten a text with a sound clip or picture lately, try deleting that message and it will hopefully go away.

http://safemanuals.com/user-guide-instructions-owner-manual/BT/SYNERGY%203105-_E

Above is your manual ..handsfree starts p.15.

Hope it helps!

Dear user place it properly on the base its charging plates must be on to the charging point

Have you got it set on auto answer? Here is the manual see page 15
http://www2.bt.com/btPortal/application?origin=mb_product_atoz.jsp&pageid=mb_pns_catalogue&portletid=mb_pns_catalogue&wfevent=link.related.content&oSiteArea=mb.corp&oPJsp=mb_product_atoz.jsp&oPt=mb_pns_catalogue&oDocumentId=editorial/user_guide/synergy_4500_ug.xml&oOJsp=content.jsp&oPg=mb_pns_catalogue&oDocumentType=User+Guide&siteArea=mb.corp&PorS=products&contentitemid=editorial/user_guide/synergy_4500_ug.xml&contentType=User+Guide&event=bea.portal.framework.internal.portlet.event&com.bea.event.type=linkclick&oLName=link.searchresults&oLDesc=2637928916

The phone at the back of the base has an adjuster check if its there if not while having a communication try using the minus sign to reduce the volume.

If the handset displays 'Searching', 'Base' or 'Range out' on the screen, this indicates that the handset has lost its link with the base. The following procedure should be followed to help resolve the problem:

• Confirm that the power lead has not been inadvertently disconnected from the base.
• Ensure that the handset batteries are correctly installed and are fully charged.
• Ensure that the handset and base are within range of each other.
• Switch the mains power off, wait five seconds and then turn it on again. This will reset your product.
• Carry out a reset procedure on both the handset and the base to return the settings back to the factory default. Your user guide will guide you through the correct procedure.
• If none of the above remedies solve your problem, please contact the helpdesk.

Get into a smaller room, its too big!

reset your phone settings

Hi,

To purchase battery,

http://www.gmkbatteries.co.uk/Cordless_Phone_Battery/BT/SYNERGY%202110/x/4/3/true.html


I can also check a place to purchase mains's charger.

But,

Check the price.If you purchase charger and battery, the price would be more than the price for the new phone.

Check the price - Only 9.9 B.Pounds.....

http://www.inest.co.uk/products/BT_Synergy_2110_DECT_Cordless_Phone.asp


I Hope i might have helped you to take a decision.

Thanks for using Fixya.

It sounds like you're pressing the green button when you pick up the phone - when the phone is in the charger and you pick it up to answer it you'll be speaking straight away, no need to press any buttons.
You can toggle between speaker and the phone by pressing the green button.

Hope this helps...

to set the time the instructions are on page 9 of the instruction manual in the getting started section.

in case you no longer have the manual....

1. press the tick/menu button twice.
2. press 0 and you hear 'to set the day and time press Star, to hear the day and time press Square.
3. press star. you hear 'please enter new day and time after the tone' enter the day (1=sun, 2=mon etc) enter the time using 24hr clock.
4. press the X/security button twice to exit.

hope this helps.

I may have a solution you can try.

1. Take handset out of cradle.
2. Press and hold bottom, right hand side, bottom button, marked "Calls"
3. Hold until "Display" shows number of calls, usually 10 and makes a bleep-type noise.
4. Now press top left button, marked "Del" in red, until the display scrolls through all 10 numbers and deletes all the numbers stored in the memory. The phone should then make a bleep noise.
5. Press "red handset symbol" (finish call) twice.
6. Replace handset onto cradle and the "new call light" should go out.

You should now be able to make calls.

Good luck !!!