20 Most Recent
Acer AL2671W 26 in. LCD Television - Page 3 Questions & Answers
Acer AT3201W LCD TV
I repaired my Acer by replacing the power supply from
http://www.power-on.com/lcd323-4m.html - $85
Acer would not sell me a replacement power supply.
Note: I needed to solder wires the new power supply to the old one,
the pinouts on the connectors on the new one would not fit the original.
Remote sensor and button switch will not turn the
I have the same problem. I only have a poor work around. Disconnect the power (or switch off using the switch underneath the TV near where the power cable connects, wait 15 seconds, then restart, It temporarily fixes the issue. I am still trying to find a proper fix
The ACER lcd tv problem
Hi
Thanks
for using FixYa. I am assuming that the sound is coming fine out of the TV as
you have not mentioned about it. However, to resolve the issue of darker or no
picture you’ll need to check the X and Y
sustain buffer boards. When either of these boards goes bad
common problems include negative image, no image, vertical or horizontal
stripes on picture, turns on and than turns off, and many more. You’ll need to
open the back off the TV and check for any swollen/bulged/leaky capacitors on these
boards and replace whichever has gone bad. If still the issue is not resolved,
then please check the power supply board. All this is only recommended if you
have electrical expertise & know how to solder/re-solder components as
these units contain high voltages even when switched off.
Please do
accept the solution if the issue is resolved or else revert for further
assistance.
Thanks
Rylee
Half of the screen displays in pink, the other
Hi
Thanks
for using FixYa. First go into the menu settings and check
whether it has a warmth tint function some TVs have various settings for
different inputs to get the best picture for the unit your using whether films
or TV programmes some have an auto setting so change depending on input source
used if that is the case select off on the auto setting. If still the issue is
not resolved then I would say that you
might have a backlight issue with this TV set. It could also be due to the
inverter circuits for the backlights. The inverter is the power
supply source for the backlights. There could also be a screen driver
problem; if it is then you have to change the entire board. All this is only
recommended if you have some kind of expertise for checking the internal
circuitry of the TV as these units have high voltages running even when the set
is switched off. Please do accept the solution if the issue is
resolved or else revert for further assistance.
Thanks
Rylee
How do I reset the whole TV?
press channel+ and volume- on the tv (not the remote controller) than you go into factory mode. You can reset certain things there.
Firmware
Sorry for my English, I’m going to try to express what I want.
I found on Internet all the firmwares of this model, also a service manual, and the programmer software to upgrade the firmware of this TV, I have the American, Australian, Pal and European firmwares, but the problem is that I haven't the interface to connect my notebook with the TV, I know that I have to connect and RS232 port with a D-SUB 15 (VGA INPUT), the problem is how to construct this interface, I want a scheme to do it or if somebody know the pin outs of the D-SUB 15 connector to transmit data that’s will help a lot. I somebody want the firmwares files and the programmer software only ask me.
Thanks in advance
Oolong
Acer LCD Monitor AL2671W - screen too bright!
I had the same problem with my TV when I purchased it used. Select the input you are having troubles with and enter "Service Mode" by pressing and holding the "VOL - " button and "CHAN + " buttons on the TV, simultaneously until the screen flashes red one time.
At this point you will be in service mode. Pressing the "MENU" button will open a service menu, which is different from the typical user menu. From the service menu you can further adjust your image settings until you have a decent picture.
Initially my VGA input looked terribly bright and washed out. Now it looks incredible!
Removing back cover
be very carefull and set tv on its face. insert a wide blade screwdriver along the side edge between the back and bezel then push down there are tiny plastic grips along the edge all the way around the back. if you can get your fingers in between give a tug up and the back will come off. provided you removed any screws from the back. it is ok to break a couple of the interlocks.
Not finding what you are looking for?