20 Most Recent Miele W1926A Front Load Washer - Page 4 Questions & Answers

Question edited for a lot more clarity. I found this hello my name is Jon and i am an authorized Miele service technician and I can help you today. are you sure that you are not misreading the fault or error code? to my knowledge there is no f 1 E error message, just an f13. which is a water intake fault, heater pressure switch. if that is the error you are getting, please look at the following link. it is to the error code list for your machine. please perform the steps listed for the f13 error under the remedy. if the remedy doesn't work I would replace the heater pressure switch and the water flow system. They are very common parts to break on these machine. the parts can be order directly through Miele by calling or going online. phone is the best way to contact them i believe. this way you can actually talk to someone who can help you better. the phone number is 1-800-999-1360. or go online to www.miele.usa.com. the link for the error codes is below. just highlight the link and right click it with your mouse to open it. http://appliancehelponline.com/miele.html thank you. and I look forward to helping you get this machine fixed in the quickest and cheapest way possible.

The error message "fit cover to main dispenser" typically indicates that the cover for the main dispenser (where the coffee beans are stored) is not properly secured. To resolve this issue, make sure that the cover is securely in place and that it is properly aligned with the dispenser. If the problem persists, you may want to consult the user manual or contact Miele customer support for further assistance.

Removing the top lid on a Miele Novotronic 500 washing machine will depend on the specific model of your machine. However, here are some general steps that may help:

1. Unplug the machine from the power supply.
2. Locate the release catch or lever on the top of the machine. This may be located on the front or back of the machine, depending on the model.
3. Press or push the release catch or lever to release the top lid. It should then be able to be lifted off.
4. If you don't find any visible lever or catch, please check the user manual of your washing machine, as some models may have a different mechanism to open the lid.
5. If the lid is still not opening, it may be stuck due to a malfunction or an error. In this case, it is recommended to contact the manufacturer or a professional technician for assistance.

It is important to be cautious when handling the top lid of the machine, as it can be heavy and fragile. It is also important to make sure the machine is not running or plugged in before attempting to open the top lid.

This means that the drain attached to the pump is clogged, remove the drain plug check fro debris and replace...you should be good to go.

Question edited for clarity. Question moved from Computers category. Wash temperatures are not able to be changed, they are dictated by the thermistor sensor and the setting of the EPROM in the control board, however, the 40' Wash temperature refers to the wash labels tags in clothes. About 20 years ago when HE detergents came out, manufacturers reduced water temperatures by 10'C, so although it is a '40' Wash', you should find the temperature is lower. Check it with an infra-red thermometer. https://usermanual.wiki/Miele/W-526.4061114030/html ..

Hey did you find the problem I have the same problem with the same washing machine!

I need the model number to be able to help you.

does your machine have a drain trap-clean that out-if you still are getting the message,there may be a problem with you drain pump-check it for blockage. the check inlet means you have a water supply problem-either blockage or no pressure coming into the machine-both supply and drain can get clogged and bring your laundry to a halt-cheers Denny

Water path control system faulty. The power-programme module (ELP) cannot register a valid position of the water path control unit within approx. 80 s of it being switched on. You have to replace water intake system. The top of the soap dispenser with pathway selector

sounds like the main motor brushes need replaced as it is overheating

• get the service manual yet/
• or call for service.?

Added Model Number to this post and deleted duplicate post. Refresh the page to see your post published. It sounds as though the water inlet valve has failed. The humming is the solenoid trying to open. https://www.google.com/search?q=miele+w5748+water+inlet+valve ..

drive motor capacitors might be getting weak

Question edited for full make and model.Question moved to Miele category.Yes, the water inlet valve is not shutting off properly. They wear and stick.Replacement is $40AUS and videos on how to change them.https://www.google.com/search?q=W820+washing+machine+replace+water+inlet+valve..

It just needs lubricating. The most likely place is the idler wheel on the belt drive. also lubricate the rear drum bearing, the fan and the front drum slides (some have oiled felt pads, so have rollers. Disconnect it from power, pull it out and tip it on its back, and your can easily get to the idler pulley and the rear bearing. To do the job fully, you remove the case. The screws are at the back. https://www.google.com/search?q=Miele+Novotronic+T490+has+developed+a+squeak ..

The hose might need to be replaced on your washing machine.

You can take help from - https://realappliancerepair.com/

The back panel is held on by screws. There should be four screws along the top of the panel, two near the bottom corners, and one in the center near the bottom. Once these screws are removed, the panel should come off easily. The belt is located under the panel, and can be replaced by following the instructions in your owner's manual. If you don't have your manual, you can usually find it online by searching for your model number. Hope this helps!

Could be a malfunctioning cycle timer