GE RM24930 Remote Control - Answered Questions & Fixed issues

028.022.026. Try these codes. If you wish to get more; check the site linked here. It has set-up code list & set-up procedure to many popular brand remote controls. See it in "Mosaic" or "Magazine" view. It will make surf easier. http://electrohelponline.blogspot.com/ Try this link too http://remotesearch.blogspot.com/

0031 0107 0164 0004 0009 0044 0054 0000 0342 0003 0125 0015 0022 0052 0087

Try the following codes for a Sylvania TV:

0062
0004
0009
0135
0189
0183
1141
0227
0456
0008
0068
0075
0141
0161

Here is a link to all the 4 digit codes for those devices:

http://www.jascoproducts.com/support/download-files/RemoteCode-4-digit.pdf


If it is a 3 digit code you need, then here is a link to all the 3 digit codes for those devices:

http://www.jascoproducts.com/support/download-files/RemoteCode-3-Digit.pdf

Just use your mouse to click on the link, which is the underlined and highlighted text just above. This will open a new web browser page automatically for you and allow you to view the information at the website indicated.

You may need ADOBE READER installed on your computer to read PDF documents. You can download this free at WWW.ADOBE.COM if necessary. Click on the DOWNLOAD ADOBE READER button on right side of the ADOBE home page when you get there, and then just follow the onscreen instructions to install it.

Good luck.

Hi,

You can programme your remote by below method

Manual code entry

1.Turn on your television or other electronic component that you want to program the remote control for.

2.Hold down the "Code Search" or "Setup" button until the LED indicator light turns on.

3.Hit the button for the component that you are programming (TV,DVD VCR, etc.). The LED light should flicker and stay on.

4.Enter the 3-digit or 4-digit code that corresponds to the TV or device that you're operating.The LED light should go off if the code is valid, but will flash if it is not. Try other codes you have.

5.Try turning the television or other programmed component off to ensure that the remote works properly, once the light has gone off.


Auto configuration


1.Turn on your television or other electronic component that you want to program the remote control for.

2.Hold down the "Code Search" or "Setup" button until the LED indicator light turns on.

3.Hit the button for the component that you are programming (TV, DVD, VCR, etc.). The LED light should flicker and stay on.

4. Press and release the "Power" until the television or other component turns off while waiting at least 2 seconds between each press.

5.Press "Enter" or "Save" once the remote has effectively turned the power off. The LED light will shut off and the remote will now operate the device.

You can get your codes from below website

http://www.jascoproducts.com/support/universal-remote-codes.asp

Thank You

Hi,

Please try to programme your GE remote to your TV

Manual code entry

1.Turn on your television or other electronic component that you want to program the remote control for.

2.Hold down the "Code Search" or "Setup" button until the LED indicator light turns on.

3.Hit the button for the component that you are programming (TV,DVD VCR, etc.). The LED light should flicker and stay on.

4.Enter the 3-digit or 4-digit code that corresponds to the TV or device that you're operating.The LED light should go off if the code is valid, but will flash if it is not. Try other codes you have.

5.Try turning the television or other programmed component off to ensure that the remote works properly, once the light has gone off.


Auto configuration


1.Turn on your television or other electronic component that you want to program the remote control for.

2.Hold down the "Code Search" or "Setup" button until the LED indicator light turns on.

3.Hit the button for the component that you are programming (TV, DVD, VCR, etc.). The LED light should flicker and stay on.

4. Press and release the "Power" until the television or other component turns off while waiting at least 2 seconds between each press.

5.Press "Enter" or "Save" once the remote has effectively turned the power off. The LED light will shut off and the remote will now operate the device.


You can get your codes from below website

http://www.jascoproducts.com/support/universal-remote-codes.asp

Thanx

Look on the back of your tv and see if it is made by a parent company (most likely it is). .

well there should be a setup button. you click and hold it untill the light blinks twise and t hen there should be this piece of paper with numbers tha came with the remote and those numbers are codes so just look for your tv manufacturer and when you fing the code thats under it input the code and then there should be red light blinking twise again

I found that these websites should have all the codes and instructions for most remotes
http://www.xdiv.com/remotes/
or http://www.remote-codes.com/

http://www.jascoproducts.com/support/universal-remote-codes.asp

Here are the 3 & 4 digit codes Philips
0062 0204 0184 0208 0205 0206 0207 0004 0189 0183 0199 0200 0288 0456 0003 0008 0068 0075 0086 0087 0141

Philips-Magnavox
0062 0204 0207 0183 0226 0288

New 3
003, 004, 006, 008, 062, 068, 069, 074, 075, 076, 086, 087, 089, 133, 141, 163, 183, 184, 189, 204, 205, 206, 207, 208, 212, 213, 288

Old 3
003, 004, 008, 012, 019, 046, 047, 062, 068, 069, 074, 075, 076, 086, 087, 088, 089

below is the online manual:

http://www.fixya.com/support/p237065-ge_rm24930_remote_control/manual-11900

http://www.envizage.com/p/737959/sumvision-zengo-remote-control.html

Hope this helps, Stan.

Try Here: http://www.jascoproducts.com/support/universal-Remote-codes.asp

goto ge.com, under the support section and enter the model of remote, it will give you the manual, and you will have the codes

reprogram control ge rm24930

look in back of remote where you put battiers there should be a sticker that will say this... turn tv on press and hold set button tell it blinks or stays lit push tv on remote push on and off tell tv shuts off press enter now you should have it

I need the instrucion, for my phlip universal control.

If your device does not respond after you have tried
all the codes for your brand, or if your brand is not
listed, try searching for your code by following these
steps.
1. Manually turn on the device (TV, VCR, etc.) to be
controlled.
2. Press and hold the SETUP button until
the red indicator stays on, then
release the SETUP button.
3. Press and quickly release the desired
device button (TV, VCR, etc.). The red
indicator blinks off once.
4. Press the ON-OFF button repeatedly
(up to 300 times) until the device to
be controlled turns off. The red
indicator blinks off with each button
press.
5. Press and release ENTER to install the code

Good luck

Hi
Here is the link for all Codes
http://www.remotecodelist.com/remotes/ge/RM24912_codes.pdf

and the Manual for instructions
http://www.remotecodelist.com/remotes/ge/RM24912_instructions.pdf

Good Luck

http://www.remotecentral.com/cgi-bin/files/dl.cgi?file=others/ge/rm24930-manual.zip&area=other

the answer should be in there