GE Logo

GE Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 7K Products
  • 211K Answers
  • 4M Views
0helpful
2answers

My ge front load washer fills then stops during cycle and does nothing else. It spins in the beginning then will not drain at the end

It sounds like the drain pump itself is damaged--the important clue was the humming noise. It could be bound up mechanically or the impeller could be damaged and just vibrating instead of spinning. The part number for the drain pump is WH23X10026. The fact that the pump was humming tells me that the 120v supply is being turned on by the main control board and that the wiring is good all the way to the pump. When I service customers, I try to save the pump if possible in clog cases. Most of the time, they aren't damaged from a simple clog. But, occasionally, the impeller cracks, or the nylon blade gets loose on the shaft, or the motor windings have defects from heat, etc.
8/19/2022 4:37:18 AM • GE Energy Star... • Answered 13 hours ago
0helpful
1answer

GE GDT580SSF2SS Profile dishwasher top rack slides out every time the door is open. The level is not an issue.

Question edited for clarity. There is a parts diagram for the upper dish rack system here. Look at parts 680, 681 and 683. It says one is an 'adjuster'. https://www.searspartsdirect.com/model/2iecv2w4l9-000432/ge-gdt580ssf2ss-dishwasher-parts ..
8/18/2022 2:58:52 PM • GE Profile... • Answered Yesterday
0helpful
2answers

GE Profile Dishwasher about 7 years old.

The washer doesn't pump water in--plumbing water pressure forces it in when the water inlet solenoid opens the valve. Check the water inlet solenoid--they are a common failure point. Look under the front of the washer behind the panel to find it--just trace the water inlet line. It connects directly to it. The valve can be stuck shut or, more commonly, the plastic coil form of the solenoid disintegrates. In any case, just replace it. Don't forget to shut off the water supply valve under the sink before you start work. Hope this helps!
8/17/2022 3:20:26 AM • GE Dishwashers • Answered 2 days ago
0helpful
2answers

How do I clear an error code FO on my GE oven

it usually means the touch pad or the oven control is defective.
8/15/2022 8:58:27 PM • GE Ovens • Answered 3 days ago
0helpful
1answer

GE dishwasher rinses, but won't fill for wash cycle

It could be a failing water inlet valve or the main control board. If it does it every time you try, it is not the water inlet, it is the Control Board. Unfortunately both parts are obsolete. Time for a new one or search for parts in stock somewhere. https://www.partselect.ca/Models/GDT545PSJ0SS/Sections/Body-Parts/?ModelID=6882101&ModelNum=GDT545PSJ0SS&mfgModelNum=&ManufactureID=2&Selected=35592F79C4D18354271BEB350E3C0B86DA4AF3F2&Position=1&mfg=GE&Type=Dishwasher&Mark=1 https://www.google.com/search?q=GE+dishwasher+GDT545PSJ0SS+parts ..
8/14/2022 11:37:02 PM • GE Dishwashers • Answered on Aug 14, 2022
0answers
0helpful
1answer

Where do I buy a replacement charcoal filter for my HMV-9305/1 OTR Microwave? Can I use ones that are GE compatible but not listed as Bosch compatible?

Your owner's manual should give you the approved filter numbers required. Then you can just go on Amazon and type in the Model # and they will normally bring you straight to the listing for the part. If that doesn't get you to one that will work you could always call the manufacture and talk to technical support, and they should be able to guide you to an approved replacement.
8/14/2022 6:32:25 PM • GE Microwave... • Answered on Aug 14, 2022
0helpful
1answer

I have a GE electric dryer that is barely a year old. I will not start when I push the button. Is there a reset button on a GE dryer?

Try pressing on the door switch and running it with the door open, if it works you need to replace the door switch
8/13/2022 6:05:50 PM • GE Dryers • Answered on Aug 13, 2022
0helpful
1answer

Zbd6900p1011 GE Monogram dishwasher leaking from bottom of the door. What can I do? Can i fix it myself?

Check the dishwasher to door seal for any defects or debris that maybe interfering with the maintaining of a proper seal.
8/13/2022 6:01:37 PM • GE Dishwashers • Answered on Aug 13, 2022
0helpful
1answer

I have a GE washer and just replaced the pressure switch and the hose but the water keeps over filling.. my valve looks good since it stops when i power off the machine..what could be wrong?

Suck some air out of hose. Needs negative pressure when empty. You can try to fill basin up to max fill level. Disconnect hose to let pressure bleed off. Drain, and you should be set
8/10/2022 1:57:32 AM • GE Washing... • Answered on Aug 10, 2022
0helpful
1answer

GE Monogram #ZISBY42DYA small amount of water leaking into dispenser tray on door

There might be a problem with the water dispenser or the water filter is not installed properly.
8/9/2022 4:05:20 AM • GE Refrigerators • Answered on Aug 09, 2022
0helpful
1answer

Slow water flow from refrigerator dispenser

The technician is correct and you could take a water sample from a normal faucet and send it in to see how high the particulate and turbidity is. Then you can decide about a whole house filter. They can be expensive so get bids.
8/8/2022 4:54:36 PM • GE Refrigerators • Answered on Aug 08, 2022
0helpful
2answers

GE XL44 Model JGBPOGEPGWH

I can't find the model number that you gave. I did find other GE XL44 ranges. Near the gas regulator of the range, there should be a conversion kit. You'll need to pull the range away from the wall to find the kit. Turn the gas shut-off to stop the gas flow and unplug the range for safety. The conversion kit includes the instructions for doing NG -> LP and back. The pictures here, https://www.appliancepartspros.com/door-drawer-parts-for-ge-jgbs20bea1ad.html , may help you find the gas line parts. There are a number of steps for the conversion. First, you need to flip a cap in the range's regulator. (When sold, the part is set for NG. You take it out and replace it after flipping it over (180) for LP.) For the stove top, take off the burner grates and burners. Next, you have to remove each burner orifice spuds (7 mm nut driver, IIRC) one at a time. Place the appropriate replacement orifice in that location. The orifice spuds are below the range surface so avoid dropping the parts. Each orifice spud has a letter with a different set of letters used for the NG and LP versions. Inside the oven, you need to access the oven orifice spud. This requires taking off panels inside the oven. Replace the orifice spud, as with the surface burners. You'll also need to adjust the air flow for the oven. Finally, turn the gas shut-off valve to on and plug in the power cord. Test the burners and adjust them following the directions in the instructions. There is a blurb about finding the conversion kit and instructions on page 42 of the user's guide, available on the product page: https://www.geappliances.com/appliance/GE-30-Free-Standing-XL44-Standard-Clean-Gas-Range-JGBS20BEAAD . The current link to the manual is https://products.geappliances.com/MarketingObjectRetrieval/Dispatcher?RequestType=PDF&Name=49-85135.PDF . I hope this helps. Cindy Wells (Since LP and NG pressures are very different, I hope your range was already converted to the LP regulator and orifice studs. Then all you just need to adjust the air/gas ratio to get a blue flame.)
8/7/2022 7:55:01 AM • GE Kitchen... • Answered on Aug 07, 2022
0helpful
3answers

How to get the clean off an ge coffee pot?

Automatic clean function
The coffee maker is equipped with an automatic clean function. After 60 brewing cycles, the clean indicator/button (22) lights up. This indicates coffee maker should be cleaned by using the automatic clean function and the charcoal filter (17) should be replaced.
NOTE: The coffee maker can continue to be used, when clean indicator/button (22) is on.
• To begin the cleaning cycle, remove the charcoal filter (17) from the water tank (10). Fill the tank with a vinegar and water mixture (1/2 vinegar and 1/2 water) or a descaling product. Press clean (22) button for three seconds. The clean indicator/button (22) flashes and the cleaning process begins.
Cleaning process:
• 24 cycles of 7 seconds brewing and 21 seconds off
• 30 minutes rest
• Brewing the remaining descaling solution
• After cleaning process is complete the clean indicator/button (22) goes off. Fill water tank (10) with clean water and run one brewing cycle to rinse the coffee maker.
• Change the charcoal filter (17) (ill. k). Reinsert the charcoal filter to the coffee maker (ill. l).
NOTE: You can use the cleaning function before reaching 60 cycles (especially if the water hardness is above normal). Press and hold clean indicator/button (22) for 3 seconds.
NOTE: The Cleaning Process takes 60 minutes to complete. You cannot cancel the cleaning process before it is complete. Unplugging the machine only delays the cleaning process.
8/5/2022 9:21:55 AM • GE 106591 Coffee... • Answered on Aug 05, 2022
0helpful
1answer

My GE GTWN4250M1WS Top Loading Washing Machine is making noises during all cycles. What should I do?

It is usually caused by worn Clutch Dogs or a fault with the Gearbox. It is a messy job and requires special tools. Call for service. Or depending on age, buy a new energy efficient front loader. Less water, electricity and detergent.
8/5/2022 3:25:24 AM • GE Washing... • Answered on Aug 05, 2022
0helpful
1answer

GE JGB860EEJ1ES Gas Range schematic wiring diagram please.

Question edited for clarity to put things in the right order and throw in some upper case letters. Three ways

Model Search ' JGB860EEJ1ES

https://www.geapplianceparts.com > parts > assembly GE® 30" Free-Standing Gas Double Oven Convection Range. JGB860EEJ1ES. Product Specifications · Owner's Manual · Installation Instructions ...

Gas & Electric Range - Wiring Diagram Location

https://products.geappliances.com > appliance > gea-sup... The wiring diagram (mini-manual/schematic) is packaged with each model. The most common locations are listed below: Behind the control panel. Taped to the right ... Missing: JGB860EEJ1ES ‎' Must include: JGB860EEJ1ES
8/4/2022 5:16:56 PM • GE Kitchen... • Answered on Aug 04, 2022
Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top GE Experts

Marvin
Marvin

Level 3 Expert

85240 Answers

Cindy Wells

Level 3 Expert

6498 Answers

Brad Brown

Level 3 Expert

19116 Answers

Are you a GE Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...