Top 20
Uniden BC72XLT Handheld Scanner - Page 5 Questions & Answers
I need codse for
You can get the frequency,s for your state and county at RadioFreq.com
How do i program numbers in my radio
To program a known frequency into your scanner:
1. Power the unit ON.
2. Press the HOLD key.
3. Enter a channel number.
4. Press the FUNC and PGM keys. The selected channel number will display.
5. Enter the desired frequency, including decimal point (ex: 151.475).
6. Press E to enter the data into memory.
7. Repeat steps 2 through 6 for additional channels.
More detailed programming information can be found in the scanner operating manual which can be downloaded/printed here:
http://www.uniden.com/pdf/BC72XLTom.pdf
For a comprehensive database of active frequencies in your area, visit:
www.RadioReference.com
Bill B
How do i program it
To program a known frequency:
1. Power the scanner ON.
2. Press the HOLD key to stop scanning.
3. Enter the desired channel number.
4. Press the FUNC and PGM keys.
5. Enter the frequency, including decimal point.
6. Press E to enter the data into memory.
7. Repeat steps 3 through 6 for other channels.
More detailed programming instructions can be found in the scanner operating manual w2ich you can download/print here:
http://www.uniden.com/pdf/BC72XLTom.pdf
For a comprehensive database of active frequencies in your area, and a lot of other useful scanning information, visit:
www.RadioReference.com
Bill B
No sound from my new Uniden UBC72XLT radio scanner
Your best bet is to send it to Uniden for factory certified repair. They may charge a little more than your local electronics shop, but they will use the correct parts and give you a quality repair with a factory warranty. You can contact them here:
http://www.uniden.com/repair/repairform1.cfm
Bill B
How to put in frequencies
To program a known frequency:
1. Power the scanner ON.
2. Press the HOLD key to stop scanning.
3. Enter the desired channel number.
4. Press the FUNC and PGM keys.
5. Enter the frequency, including decimal point.
6. Press E to enter the data into memory.
7. Repeat steps 3 through 6 for other channels.
More detailed programming instructions can be found in the scanner operating manual w2ich you can download/print here:
http://www.uniden.com/pdf/BC72XLTom.pdf
For a comprehensive database of active frequencies in your area, and a lot of other useful scanning information, visit:
www.RadioReference.com
How do i program this
To program a known frequency into your BC72XLT:
- Power the scanner ON.
- Press HOLD to stop scanning, then enter the number of the channel that you wish to program (1 - 100).
- Press the FUNC and PGM keys.
- Enter the frequency, including the decimal point.
- Press E to enter the data into memory.
More programing information can be found in the scanner operating manual, which can be downloaded/printed here:
http://www.uniden.com/pdf/BC72XLTom.pdf
For a comprehensive database of active frequencies in your area, visit:
www.RadioReference.com
Bill B
How do i find the 6 pre programmed emergency
Repeatedly pressing the HOLD key will advance the unit through all channels and bring up anything that you've programmed into it, and repeatedly pressing the SVC key will advance the scanner through the preprogrammed services (police, fire, marine, etc.). For more information you can download/print your scanner's manual here:
http://www.uniden.com/pdf/BC72XLTom.pdf
For a comprehensive database of active frequencies in your area, visit:
www.RadioReference.com
Bill B
I need a police frequency book naples fl
Don't buy a book -- for a no-cost comprehensive database of active frequencies in your area, and a lot of other useful scanning information, visit:
www.RadioReference.com
Bill B
My scanner won't turn on
Make sure you have fresh new batteries,and installed correct,check the battery connections,sometimes thes have been known to corrode from leaking,or check that you have the switch where the battery are located in the proper setting.....hope this helps....
I have a Uniden BC72XL scanner and cats knocked it
In your manual, if you have one, if not look it up on the internet. There are ways with all these types of communications, to reset to manufacturer and factory settings at time of new purchase. Then proceed forward in programming.
Bc72xlt handheld scanner
No. The BC72XLT accepts keyboard programming only. For detailed instructions you can download/print the operating manual here:
http://www.uniden.com/pdf/BC72XLTom.pdf
BillB
Not finding what you are looking for?