Top 20 Napoleon 36" Zero Clearance Top/Rear Vent Natural Gas Fireplace with Black Door Questions & Answers

I had this exact problem. Open the glass front. Take a piece of fine steel wool and clean the little metal ends where the flames ignite. Sometimes they just get gummed up. It prevents enough flow from getting through to maintain a flame.

Yes and no...... If the fireplace wont turn on from that switch, Most likley a diffrent switch

sounds like bad flame sensor this is a safety if it doesnt sense flame it will shut the gas valve off

Get someone to come and do this correctly. You have a possible carbon monoxide poisoning hazard!!

bad thermocoupler

Electrical short in the wires somewhere, at ignition control module, possibly. That what I would check for 1st, intermittent problems are the worst to diagnose, and sometimes the easiest?

Do you mean the thermo-couple ??

by pass the switch, if fireplace runs, then replace the switch

• I'm going to assume your fireplace has a pilot light.
• Follow the little holes in the burner that lead to the pilot light.
• Make sure the pilot flame is pointing directly at the closest burner hole. (adjust if necessary).
• Often, you will need to sprinkle a layer of "glowing embers" in this area. The embers will help the gas travel to the pilot light and ignite.
• Always start your propane appliance on "High" never "Low". Cold propane likes to drop to the bottom of the firebox and accumulate until it reaches the pilot (this is called delayed ignition). Keeping it on "high" will help the fuel travel over to the pilot without buildup.

Despite the simplicity of a Millivolt system,troubleshooting them is often not as simple, if you go by the book using a Volt/Ohm meter to test the generator and gas valve. The Pilot Generators are less tricky as they all put out 750 mv or 3/4 of a volt out of the system, in the system is where each result will be specific according to what gas valve is used, not all gas valves have the same ohm's values, and many newer gas valves cannot be ohmed due to the design! They will read open every one of them. The way to make it simple and assure you never get any call backs is to take a AA battery and attach a wire to each end of the battery, Radio shack sells battery boxes with leads built in for several dollars. Remove the 2 leads from the gas valve coming from the pilot generator and replace them with the AA battery leads If the gas valve operates normally via battery, it is a good gas valve, if not it is bad. If you apply voltage to the gas valve and get zero amp draw,the gas valve is bad. Do not leave the battery in place and operate the unit in this manner unless you are able to be diligently watching it, never sleep or leave etc, it is strictly for emergency use or testing. Old time units had no pilot safety, the pilot valve was manually operated just like a garden hose, if the wind blew it out it still kept coming, however as natural gas is lighter than air it will vent if it is allowed to via the flue, propane units must have 100% safety for the pilots operation as propane is heavier than air and will not vent, it settles in the lowest spot making propane more dangerous in that respect than natural gas is. 750 mv is 3/4 of 1 volt, not much power, the thermopile makes this power by having 2 dissimilar metals co joined in the end of the thermopiles that impinges the pilot flame. A temperature differential must be maintained across the thermopiles end, if the entire end of the thermopile is hot the power will drop off or stop all together, thus extinguishing the pilot. Many homeowners make the mistake of setting the thermopile too far into the flame, heating the entire end, not just the top 1/3 portion thinking this will bake it into submission, or force it to make power when in reality it does the opposite.

This is often a result of insufficient oxygen to allow combustion.Check your venting for blockage.

Thermocouple keeps the pilot lit.Thermopile keeps the burner lit.Please specify what won't stay lit...If it's the burner, you may need to change the thermopile as well.If the pilot still won't stay lit, you will want to make sure that the pilot flame is large enough to completely engulf the thermocouple and keep it hot. If it's too small, you may need to take some compressed air and blow out the pilot hood to remove any blockage.

Do not operate this fireplace until problem is solved.Could be low gas pressure, or dirty combustion parts, or bad gas control valve.Contact gas company immediately for specialist in area.If burner is dirty and clogged, then unburned, explosive gas can be going up the flueway. This is a dangerous condition that needs to be addressed before putting fireplace back into service.Web-search your specific brand and model number, and include .pdf in search parameter for possible downloadable product manual.Read product manual for advisories and maintenance and troubleshoot and warranty. If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

light your pilot and take a light to the termopile (right beside your pilot it sticks out to get heat from your pilot. hold lighter for 5 seconds and turn gas on

Please define the ACTUAL PROBLEM please!

1st guess: moving the insert shook loose some rust in the pilot assembly, which is now blocking the flow of gas to the pilot.Remove pilot hood if possible and/or clean out with compressed air.good luck :-)

Not thermopile. If your pilot will not remain lit, you need a thermo-couple. This is the device that allows the pilot to remain lit.If you can't even get it lit, you will need to check if there is blockage preventing gas from coming out of the pilot orifice.

My guess is that you will need a GZ550 found HERE.Alternatively, you could use a universal fan kit like THIS ONE.The universal fireplace fan kit will be an easier installation and utilizes an electronic speed control.

looking where to buy a thermocouple for natural gas fireplace cgn 300tq

Natural gas does not come in canisters for residential or commercial use. Unless the manufacture makes a conversion kit from Natural gas to LP gas, and you perform this conversion, do not use the range. The gas is not burning properly, and is omitting high levels of carbon monoxide!