GWM Florid 1.5 Head cylinder bolts settings (torque)

here are the torque settings for the cylinder, main bearing, and crank cup on a GWM CB 150 VVT: Cylinder: 40 N-m (29 ft-lb) Main bearing: 20 N-m (14 ft-lb) Crank cup: 25 N-m (18 ft-lb) It is important to follow the torque settings specified by the manufacturer to ensure that the engine is properly assembled and that the components are not damaged. Here are some additional tips for assembling the GWM CB 150 VVT engine: Make sure that all of the components are clean and free of dirt or debris. Use the correct size and type of gaskets and seals. Apply a thin coat of engine oil to all of the moving parts. Torque the bolts and nuts evenly in a criss-cross pattern. Do not overtighten any of the bolts or nuts.

most those bolts are TTY and are not reused.
and are set by angle. not torque.
I guess you never worked modern engines, or read the service manual first for all the steps in order ?
2.0L gas?
2.0. is not any suzuki engine name at all
and there are four(4) 2.0L engine used, 2 gas and 2 diesel
we can not guess engines, is it a USA car or not? I only answer for USA.
2.0 DDIS or AWD version < my guess is SuZ J20b?
2.0L vvt and vvt-i

SM< words , USA 2.0L gas VVT ,, (2.0L VIN 5, 6th digit?)

Before installing the cylinder head to the cylinder block, turn the crankshaft and position key within the specified range (30-90°) in the counterclockwise direction from the top.
Turn the crankshaft and position key within the specified range/,,
Crank key not UP, but before UP, 30 to 90 before
then
Install the cylinder head to the cylinder block.(do not lose 23 dowel pins)

1. Step 1: Apply engine oil to the cylinder head No. 1 bolt threads.
2. Step 2: Tighten the cylinder head No. 1 bolts to 15 ft. lbs. (20 Nm), evenly and gradually, in sequence.NOTE
   Use a 12-point socket wrench to tighten the cylinder head No. 1 bolts.
3. Step 3: Tighten No. 1 cylinder head bolts to 30 ft. lbs. (40 Nm).
4. Step 4: Tighten No. 1 cylinder head bolts an additional 60°.
5. Step 5: Tighten No. 1 cylinder head bolts an additional 80°.
6. Step 6: Tighten No. 2 cylinder head bolt to 19 ft. lbs. (25 Nm).
   Cylinder head tightening sequence

I never build engines off internet rumor , even mine
I buy the service manual based of VIN form Suzuki,

Yes, I can help you with the cylinder head torque wrench setting for your Hyundai Atos 1.0cc. Here are the torque specifications:

First pass: Tighten all bolts to 18 lb-ft (25 Nm)
Second pass: Tighten all bolts to 45 lb-ft (61 Nm)
Third pass: Tighten all bolts to a final torque of 65 lb-ft (88 Nm)
It's important to tighten the bolts in the correct sequence. The sequence is as follows:

10 6 2 3 7
9 5 1 4 8

Note: The numbers above refer to the cylinder head bolts in the correct sequence. Always use a calibrated torque wrench to ensure that the bolts are tightened to the correct specification.

I hope this helps you with your cylinder head installation. If you have any further questions or concerns, feel free to ask.

Question edited for clarity.

This is a solely South African vehicle. You always need to specify the torque settings for the part, otherwise search results give to the torque the engine produces. This search query is for 'cylinder head torque'. Your results will be better than mine here in North America.

https://www.google.com/search?q=GWM+Steed+5+2.0+vgt+diesel%2C+cylinder+head+bolt+torque

..

Chery Tiggo 2.0 liter engine.
cylinder head torque sequence: 7 6 2 4 9 .......................................... 10 3 1 5 8
Is's done in 3 stages 1st stage 45 Nm......
2nd stage 90 degree turn, or a 1/4 turn......
3rd stage 90 degree turn, or a 1/4 turn.......

Camshaft bolts inlet and exhaust share the same torque settings 120 Nm

Cylinder head bolts MUST be replaced.

Main bearing cap Bolts: 1st 45Nm.......
2nd 180 degree turn, or 1/2 turn.......
Connecting Rod Bolts 1st 25Nm......
2nd 90 degree turn or 1/4 turn

Lower cylinder Block bolts 23 Nm........
Camshaft bearing cap bolts: 11Nm

Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.

Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.

B2500 4 Cylinder

Torque sequence: --------- ' 10 6 2 4 8 ' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51 Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final tighten all bolts an additional 90 to 100 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.

B3000 3.0 6 Cylinder

Torque sequence ---------- ' 6 4 2 8 ' ' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque to 73 Ft/Lbs

B4000 4.0 6 Cylinder

Torque sequence --------- ' 5 1 3 7 ' ' ' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs Step 3: turn cylinder head bolts in sequence an additional 90-degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.

Good luck with this job!

Torque settings for cylinder head bolts for Skoda Fabia 1.4 16v

Cylinder head bolts tightening order:



IMPORTANT NOTE: RENEW BOLTS!

Stage 1: Tightening torque = 30 Nm
Stage 1: Tightening torque = 90 Degrees
Stage 1: Tightening torque = 90 Degrees

Please do rate my response. Thanks!

Hope this helps, from autozone site. Curt
Application:
Cylinder head bolt torque sequence

Note :
Torque sequence:
---------
front | 3 1 6 |
of | |
vehicle | 5 2 4 |
---------
Step 1: Lightly oil cylinder bolt threads & washers
Step 2: Torque to 22 Ft/Lbs
Step 3: Torque to 51 Ft/Lbs
Step 4: Loosen all bolts 180 degrees
Step 5: Loosen all bolts 180 degrees
Step 6: Torque bolts 1 & 2 to 25 Ft/Lbs
Step 7: Torque bolts 3, 4, 5, 6 to 11 Ft/Lbs
Step 8: Turn all bolts an additional 80 to 90 degrees
Step 9: Turn all bolts an additional 80 to 90 degrees
*** CAUTION ***
engine uses Torque To Yield head bolts (TTY) that
permanently stretch during the initial installation.
New head bolts must be used when cylinder head is
replaced or re-installed to obtain proper Torque.

Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): Foot pounds (Final torque) Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. Foot pounds (Final torque) Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.